SMC Networks PFMV5 instruction manual Model Indication Method, Specifications

Page 2

• Prepare maintenance space.

• Do not drop or bump, or apply excess impact.

• Do not pull the lead wire forcefully, not lift the product by pulling the lead

wire. (Tensile force 49N or less).

• Mount a sensor by observing the proper tightening torque.

• Install or connect the flow sensor so that the flow direction specified on the

label matches with actual flow direction.

• Pipe the flow sensor after eliminating dust in piping by air blow to avoid

failure and malfunction.

• Use dry air which complies with the quality grade of ISO 8573-1 1.1.2 to

1.6.2 : 2001.

• If the entering of foreign material to the fluid is possible, install and pipe the

filter or the mist separator to the inle to avoid failure and malfunction.

• Avoid repeatedly bending or stretching the lead wire.

• Wire correctly.

• Do not wire while the power is supplied.

• Do not wire in conjunction with power lines or high voltage lines.

• Wire as short as possible to avoid the affect of noise and surge.

• Never use in the presence of explosive gases.

Dimensions and Names of Individual Parts (unit: mm)

34.40.8

 

 

10

FLOW SENSOR

 

 

 

 

 

 

 

 

Piping

 

 

 

 

 

2 M5

0.8 Thread depth 3.8

 

 

 

1

IN

15.2

 

 

2 OUT

 

18

 

 

(15)

 

 

 

 

 

7.1

 

 

3

14

Mounting

 

 

2

3.4

 

 

 

 

 

 

 

• Do not use in an area where magnetic field is generated to avoid

malfunction of sensor.

• Do not operate where the flow sensor is exposed to water.

• Do not use the sensor for poisonous substances, deleterious substances

and corrosive gas. This sensor is not a explosion proof. Do not use for

flammable gas.

• Do not apply heat cycle to the flow sensor.

• Do not used in an area where surges are generated.

• Sensors are not equipped with surge protection against lightening.

• Avoid using sensors in an environment where the likelihood of splashing or

spraying of water, chemicals, and oil to avoid failure and malfunction.

• Consider operating environment according to protection class.

• Do not use the flow sensor where exposed to vibration or impact. Vibration

may interfere correct measurement.

• Flow sensor has to be fixed when used.

• Operation under low temperature (5 or less) leads to cause damage or

operation failure due to frozen moist in the fluid or air.

• Do not short circuit the load.

• Maintenance and inspection should be performed periodically.

With L-type bracket Mount on one side

(25.7)

 

 

 

 

10

12

 

 

.5

 

5

 

 

 

 

x

4

 

 

2

 

 

 

 

 

FLOW

 

 

24 34

SENSOR

 

 

 

 

Mount on both sides

10 x n + 24 (n=1 to 5)

 

 

10 x n + 14

 

 

10

 

 

34 24

FLOW

FLOW

FLOW

 

SENSOR

SENSOR

SENSOR

 

 

.5

 

x

4

2

 

 

 

• Analog output may fluctuate by 2 to 3% for 5 minutes after supplying power

to the flow sensor.

• Do not poke inside a piping port with a stick.

Model Indication Method

 

PFM

-

-

 

Type

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Model

Contents

 

 

 

 

 

 

 

 

 

V5

Remote type sensor

 

 

 

 

 

 

 

 

 

Measurement flow range

Model

Contents

05

0.0 to 0.5

/min

10

0.0 to 1.0

/min

30

0.0 to 3.0

/min

05F

-0.5 to 0.5

/min

10F

-1.0 to 1.0

/min

30F

-3.0 to 3.0

/min

 

 

 

 

Output specification

 

 

 

 

 

 

 

 

 

 

 

Model

Contents

 

 

 

 

 

 

 

 

 

 

1

Analog (1 to 5V)

 

 

 

 

 

 

 

 

 

 

 

 

Operation manual

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Model

 

 

 

Contents

 

 

Nil

With Operation manual (in Japanese and English)

 

 

N

Without Operation manual

 

 

 

 

 

Option(Included in the same package)

 

 

 

 

 

 

 

 

 

Model

 

 

 

Contents

Nil

Without L-type bracket

A

With 2 L-type brackets and 2 mount screws M3 x 15L included for 1station

2

OUT

L-type bracket

 

2

OUT 2

OUT 2

OUT

L-type bracket

(Tapped)

 

20

 

20

 

 

 

 

(Tapped)

 

 

 

 

 

 

 

 

 

 

 

 

 

9.1

 

1

9.1

2

 

 

 

1

2

 

 

 

 

 

 

 

 

 

 

 

L-type bracket

 

 

 

 

 

 

 

(Through hole)

 

 

 

 

Specifications

Model

PFMV505

PFMV510

 

PFMV530

PFMV505F

PFMV510F

PFMV530F

Measured fluid

 

 

 

Dry air, N2

 

 

 

 

(Air quality class is ISO 8573-1 1.1.2 to 1.6.2 : 2001)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Flow rate /minNote1)

0 to 0.5

0 to 1

 

0 to 3

Note2)

-1 to 1

Note2)

Note2)

(measurement range)

 

-0.5 to 0.5

 

-3 to 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Repeatability

 

 

 

2%F.S. or lessNote3)

 

 

 

 

 

 

 

 

 

 

 

 

 

Pressure

 

 

2%F.S. or less (0 to 300kPa)

 

 

characteristic

 

 

5%F.S. or less (-70 to 0kPa)

 

 

(0kPa referenceNote4))

 

 

 

 

Temperature

 

 

2% F.S. or less (15 to 35

)

 

 

characteristics

 

 

5% F.S. or less (0 to 50 )

 

 

(25 reference)

 

 

 

 

Pressure rateNote5)

 

 

 

-70kPa to 300kPa

 

 

 

 

 

 

 

 

 

 

 

 

Operating pressure

 

 

 

-100kPa to 400kPa

 

 

 

rangeNote6)

 

 

 

 

 

 

Proof pressure

 

 

 

500kPa

 

 

 

 

 

 

 

 

 

 

 

 

 

Analog output

 

 

At voltage output : 1 to 5V

 

 

 

(Non-linear output)

 

Output impedance : approx. 1k

 

 

 

 

 

 

 

 

 

 

 

 

Response time

 

 

5ms or less (Response 90%)

 

 

 

 

 

 

 

 

 

 

Source voltage

12 to 24VDC

10%, ripple(p-p) 10% or less (Protected against inverse connection)

 

 

 

 

 

 

 

 

 

 

Power consumption

 

 

 

16mA or less

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Enclosure

 

 

 

IP40

 

 

 

 

 

 

 

 

 

 

 

 

 

Operatingfluidtemp.

 

0 to 50 (No freezing or condensation)

 

 

 

 

 

 

 

 

 

 

 

 

Operating temp. range

 

0 to 50 (No freezing or condensation)

 

 

 

 

 

 

 

 

 

 

 

Resistance

Storagetemp.range

 

-10 to 60 (No freezing or condensation)

 

 

 

 

 

 

 

 

 

Withstand voltage

 

1000V AC, 1min Between battery and the body

 

 

Operatinghumidityrange

 

35 to 85%R.H. (No condensation)

 

 

 

Storage humidity range

 

35 to 85%R.H. (No condensation)

 

 

 

 

 

 

 

 

 

 

 

 

 

Insulationresistance

50M

or more(500V DC Mega) Between battery and the body

 

 

 

 

 

 

 

 

 

 

L-type bracket

Vibrationresistance

10 to 150Hz 1.5mm amplitude

When optional part is needed by part alone, or to be mounted to the manifold, please order by part number below.

ZS - 36 - A

Stations

1

1 stn

2 L-type brackets, 2 mount screws M3 x 15L included

2

2 stns

2 L-type brackets, 2 mount screws M3 x 25L included

3

3 stns

2 L-type brackets, 2 mount screws M3 x 35L included

4

4 stns

2 L-type brackets, 2 mount screws M3 x 45L included

5

5 stns

2 L-type brackets, 2 mount screws M3 x 55L included

98m/s2 acceleration in X, Y, Z directions for 2 hours(Power is not supplied)

Impact resistance

980m/s2 X, Y, Z directions

3 times for each(Power is not supplied)

Port size

M5 0.8 (tightening torque : 1 to 1.5N•m or less)

 

 

Fluid contact material

PPS, Si, Au, SUS316, C3604(Electroless nickel plating)

 

 

Lead wire

3 core vinyl cabtire cable 2.6, 0.15mm2, 2m

 

 

Weight

10g (without lead wire)

 

 

 

Note 1) Converted value of volume flow at ANR (20

, 101.3kPa, 65%R.H.).

Note 2) Analog output shows 3V when flow is zero. Changes to 5V side when flow direction is IN OUT. 1V side when OUT IN.

Note 3) %F.S. in the table takes 4V (1-5V) as a full scale. Note 4) 0kPa means release to the atmosphere.

Note 5) Applicable pressure range.

Note 6) Pressure range satisfies product specification.

Image 2 SMC Networks PFMV5 instruction manual Model Indication Method, Specifications
Contents Phone Safety InstructionsUse UL approved product for direct current power supply Otherwise it can cause injurySpecifications Model Indication MethodPFMV5 series recommended fitting list Piping CircuitRecommended fitting list