RULES FOR SAFE OPERATION (Continued)
18.DISCONNECT TOOLS. When not in use, before servicing, or when changing attachments, blades, bits, cutters, etc., all tools should be disconnected from power supply.
19.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjust-
ing wrenches are removed from tool before turning it on.
20.AVOID ACCIDENTAL STARTING. Don'tcarry
21.MAKE SURE YOUR EXTENSION CORD IS IN GOOD CONDITION. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resultingin loss of
power and overheating. A wire gage size (A.W.G.) of at least 14 is recommended for an extension
cord 100 feet or less in length. A cord exceeding 100 feet is not recommended. If in doubt, use the
next heavier gage. The smaller the gage number, the heavier the cord.
22.OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords suit- able for use outdoors. Outdoor appi'ovedcordsare marked with the suffix
23.KEEP CUTTERS CLEAN AND SHARP. Sharp
cutters minimize stalling and kickback.
24, KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from cutters. Do not reach un- derneath work while cutter is rotating. Do not at- tempt to remove material while cutter is rotating.
25.NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes.
26.INSPECT TOOL CORDS PERIODICALLY and if damaged, have repaired at your nearest Sears
Repair Center. Stay constantly aware of cord loca- tion.
27.INSPECT EXTENSION CORDS PERIODICALLY and replace if damaged.
28.KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brakq fluids, gaso- line,
29.STAY ALERT. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.
30.CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged shouldbe carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving pads, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.
A guard or other part that is damaged should be propedy repaired or replaced by an authorized service center unless indicated elsewhere in this instructionmanual.
31.DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.
32.Inspectfor and remove all nails from lumber before routing.
33.DO NOT USE TOOL UNDER "BROWN-OUT" OR
OTHER LOW VOLTAGE CONDITIONS. Also, do
not use with any device that could cause the power
,supply voltage to change.
34.DRUGS, ALCOHOL, MEDICATION. Do not oper- ate tool while under the influence of drugs, alcohol,
or any medication.
35.WHEN SERVICING USE ONLY IDENTICAL CRAFTSMAN REPLACEMENT PARTS.
36.POLARIZED PLUGS. To reduce the risk of electric shock, this tool has a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outletonlyone way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electricianto install the proper outlet. Do not change the plug in any way.
37.SAVE THESE INSTRUCTIONS. Review them fre- quently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructionsalso.
Illl | IIIII | =lllll I | ,llll | I | I,I |
ll
The operation of any router can result In foreign objects being thrown Into your eyes, which can ! result In severe eye damage. Before beginning powertool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or atandard safety glasses with side shields, i
available at Sears Reta!!Stores. | J |
Page 3