Sears 315.17473 owner manual Maintenance

Page 11

MAINTENANCE

GENERAL

Only the partsshownon parts list,page 15, are intendedto be repairedor replaced by the customer. All other parts representan importantpart of the doubleinsulationsystem and shouldbe serviced only by a qualified Sears service technician.

Avoid using solvents when cleaning plastic parts. Most plasticsare susceptible to various types of commercial solventsand may be damaged by their use. Use clean clothsto removedirt, carbon dust,etc.

When electdc tools are used on fiberglassboats, sports cars, wallboard,spacklingcompounds,or plaster, it has been found that they are subject to acceleratedwear and possible premature failure, as the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutator,etc. Consequently,itis not recommendedthat thistoolbe usedfor extendedworkon anyfiberglassmaterial, wallboard,spacklingcompounds,or plaster. During any use on fiberglassit is extremely importantthat the tool is cleanedfrequentlyby blowingwith an air jet.

PROPER CARE OF CU'I'FERS

Get fastermore accurate cuttingresultsby keepingcutters cleanand sharp.Removeall accumulatedpitchandgumfrom cuttersaftereach use.

A cuttersharpeningkit (Item No. 9-66501) is availablefrom

Sears RetailStores.

PROPER CARE OF COLLET

From time totime, italso becomes necessaryto cleanyour colletand colletnut.To do so, simplyremovecolletnutfrom colletandclean thedustandchipsthathavecollectedThen. returncolletnut to its originalposition.

LUBRICATION

When sharpening cutters, sharpen only the Inside of the cuffingedge. Never gdnd the outside diameter. Be sure when sharpening the end of a cutter to grind the clearance angle the same as originally ground.

LIGHT BULB REPLACEMENT

See Figure 14.

1.UNPLUG YOUR ROUTER.

2.Remove cutterfrom muter.

3.Adjustmuter to maximum height.

4.Removescrews (A) and subbase(B). See Figure14.

5.Removescrew (C) and work lightlens (D).

6.With bulb(E) pointingtowardyou,pushbulbin and turn to the left to remove from bulb socket. NOTE: Light bulb removaland installationis similarto removingand installinga standardautomotivebulb.

7.Installnew bulb by reversingthe above procedure.

8.Reassembleall parts and tightenscrews securely.

All of thebearingsin this toolare lubricatedwitha sufficient amountof highgrade lubricantfor the life of the unit under normaloperatingconditions. Therefore, no further lubrica- tionis required.

Page 11

Image 11
Contents SEARS, Roebuckand CO., Hoffman Estates, IL Soldonly bySEARS, Roebuckand CO Dept WA Hoffman ESTATES, IL Full ONE Year Warranty on Craftsman Electronic RouterDouble Insulation is a concept in safety, in electric IntroductionDo not USE Tool Under BROWN-OUTOR Do not USE Tool if Switch does notVariable Speed OperationKnow Your Electronic Router Wrench Storage Area INSTALLING/REMOVING CuttersDust BAG Assembly To Install BAGDepth Stop Rings Depth of CUT Adjustments See Figures3Greaterthan 1/8 Electrical Connection Think Safety by Thinking AheadPractice Before Actual USE RoutingForcefeeding Proper FeedingTOO Fast Speed Selection Rate of FeedGuide Inside Routing with Guide Bushings Depth of CUTDirection of Feed and Thrust 2ND. Passj Guide OutsideExtension Cords Starting and Ending a CUT Internal RoutingTOP Edgeshaping Edging with Pilot BitsMaintenance To make adjustments to depth adjusting ring Switch ReplacementDepth Adjusting Ring Depth Adjusting Ring AccessoriesPage14 Parts List Craftsman