Sears 315.220100 operating instructions Making Other Cuts, Cutting Long Workpieces, See Figures 49

Page 53

MAKING OTHER CUTS

See Figures 49 - 50.

Variations from the basic cuts include cutting long workpieces and non-through cuts.

When making one of the following cuts, follow the instructions that apply for the basic cut, depending on the position, shape, and size of the wood. Do not attempt these cuts until you are skilled with the basic cuts.

CUTTING LONG WORKPIECES

See Figure 49.

Place a support the same height as the saw table nearby for the cut work.

,_, WARNING: Make sure the blade guard is lowered and is working properly to prevent

possible injury.

,_, WARNING: Never put your hands within 3 in. of the blade when it is on.

Make sure the wood does not touch the blade

before you turn on the saw with the switch on the arm. Let the blade build up to full speed before it contacts the wood.

When the work is completed, press the switch off and remove the key.

SUPPORTLONGWORKPIECES

J

Fig. 49

53

CRRFTSMRNRADIALSAW 315.220100

Image 53
Contents PRO Craftsman +Full ONE Year Warranty on Craftsman Radial ARM SAW Riving Knife to Blade Installing Rip Always Wear Safety Glasses with Side Safety Alert SymbolRead ALL Instructions MeaningDo not USE a Person AS a Substitute Avoid Awkward Operations and HandBe Sure the Blade Path is Free Do not Remove the Saws Blade GuardNever Perform ANY Operation Free Turn OFF SAW if a Strange Noise or Grounding Instructions Speed and WiringExtension Cords Electrical ConnectionMotorcover PAN Headscrew Changing VoltageSee Figures 2 RAFTSMANRADIALSAW315.22010010 RPMResin Throw-Back Asticky,sap-basedsubstance SAW Assemblyshownas Packed CRnFT$MRNRADIAL SAW315.220100 Bcde Channellock Pliers Framingsquare CRRFTSHRWRADIALSAW315.22010016 MadeintaiwanAdvertenciawarning Control CSee a Know Your Radial SAWMethod of Operation YokeSee Figures 9A 9D CP,nFISMANRADIAL SAW315.220100 Dustguide Holddown See Figures IOA 10C Assembung LEG StandSee Figure Mounting SAW to LEG StandAttachung Elevating Handwheel See Figures 13A- 13C Instalung the Yoke AssemblyArmviewedfrombelow Lockwasher Carriagestopscrew Carriagearm LockknobAttaching Table Supports Removing the BladeArbor Tableflat Supportwasher Square Bead BoltSetting the Yoke Clamp Setting the ARM Lock KnobSee Figures 17A 17B Yoke LEGSee Figures 18A- 18C Setting the Bevel Lock LeverRear Coverscrews Hexbolt HEX NUT2 Adjusting the Column TubeSee fLgures 20A 20D Column SupportColumn Elevation AdjustmentRotation Adjustment See Figures 21A 21B Adjusting the Carriage BearingsCarriagesearing Graspand Hold Eccentricscrew WrenchSee Figures 22A 22B Leveung the Table SupportsSee Figures 23A 23C Front Table23A Base. See BJnstalung Rear TABLE, Spacer TABLE, FENCE, and Clamps Leveling the Front TableSee Figures 25A 25C Reartablefence SpacertablefronttableSee Figures 26A 26C Nstalung Blade and Blade GuardLoosen Blade Rotation Tighten Blade ArborCorrectalignmentof Therivingknife Antfkickpawls Rivingknife Ontop of Fence TOO Farleftof BladeRivingknifetoofar Rightof Fenceand Blade Nstalling RiP Scale Ndcators Screws Ripscale Indicator Speednut Carriage SpringLinealongthisedge Framing Aligning the ARM for Cross CutsLockknob Yoke Lock Handle FramingAligning Blade to Table AT 0 Bevel Bladesquareto Table Noadjustmentneeded FramingArmlockknob BladeSquaring Blade to Fence AdjustmentSee Figures 31A 31C ARM LockknobAdjustment GAP Needed Bevel Lock Lever Noadjustment NeededParalleling Blade to Table See Figures 32A 32COUT-RIPSCALEON Leftsideof ARM RIP-SCALEINDICATOR Aligning the RIP Scale IndicatorsSee Figures 33A 33B CarriagelockknobBarrel Fitting Installing Control CUT DeviceAssembly Check Alignment of ARM and Blade Using Laser Types of Cuts Basic Operation of the Radial ARM SAWCross Cuts Mitercut BevelcutInsertswitchkey Switchon Switchoff Switch and Switch KEYCauses of Kickback Avoiding KickbackPushsticks Cutting AidsPushblocks FeatherboardsTableclamps Armlock Handle Switch Handle BevelMaking a Cross CUT Armmiterscale Lockknob Yoke Bladeguard Handle Bevel Indicator Ercut LockleverMaking a Miter CUT Beveledcut Lockknob ARM Making a Bevel CUTHandleyokelock Handle Riving Elevating HandwheelMaking a Compound Cross CUT Yoke Armpivotlatch SwitchyokelockCUT Elevating Handwheel MiterscaleSwitch Holddown Elevating Handwheel Infeedfor Inripcutting RIP CUT Hazards and PrecautionsSetting UP a RIP CUT See Figure Review the Hazards and Precautions Irip CUT Switch Making a RIP CUTInfeedfor OUT Ripcutting ANTI-KICKBACK PawlsCutting Long Workpieces Making Other CutsSee Figures 49 SupportlongworkpiecesNON-THROUGHCUT NON-THROUGH CutsBladenutblade Arbor AlignmentMounting the Laser Guide Cover MOTOR/ELECTRICAL General MaintenanceCausesolution Cause Solution See Aligning Arm for Cross Cuts in Adjustments section See Adjusting the Column Tube in Assembly sectionSee Setting the Arm Lock VZheelin the Assembly section See Squaring the Blade to Problem Cause SolutionAssembly section Fence in AdjustmentsSee Setting the Arm Lock CRRFTSMnN Radial SAW315.220100 See Figure Craftsman Radial ARM SAW- Model noSee Figuresf and G ARM SAWKEY Part NO. Number Parts List for Figure aDescription Quan KEY Part NO. NumberSee Figure C See FigureDescription Parts List for Figure BKeypart NO.NUMBER Figure C KEY Part Number Description Quan Parts List for Figure CFigure D Parts List for Figure D £RRFTSMRNTABLESAW315.22010072 Figure EKEY Part Number Description Parts List for Figure ECraftsman Radial ARM SAW Model See Figure G Figure F75CRRFTSMRN RADIALSAW315.220100 Parts List for Figure FFigure H Figure GParts List for Figure G Figure H Description Quan Parts List for Figure HRadial ARM SAW- Model no CraftsmanParts List for Figure Figure J See Figure KParts List for Figure J Figure K Parts List for Figure K Sears