Sears 113.23611 Recommended, Glossary of terms for woodworking, Switch Black, Remedy Suggested

Page 17

diagram

SWITCH

BLACK

wHITE .... ,,

GREEN: ....

recommended

accessories

Item

Sears Number

Leg Set

9-22244

Blades

See Catalog--For 5" long,

pin end type blades 9-26873--medium radius cuts in wood up to 11/2" thick 9-26879--fine radius cuts in wood up to 1/4" thick

The above recommended accessories are current and were available at the time this manual was printed.

glossary of terms for woodworking

1.Kerf--theslot cut by the blade

2, Leading Edge--the edge of the work piece which is pushed into the blade first.

3, Sawblade Path--Thearea of the workpiece directly in line with and moving toward the sawblade edge.

4.Blade Tooth Set--the distance that the edge of the sawblade tooth is bent (on set) outward from the side of the blade.

 

= Trailing Edge--the workpiece edge last cut by the

trouble shooting

sawblade.

Work Piece--theitem on which the cutting operation

 

6.

 

is beina preformed.

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF",

REMOVE KEY AND REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE TROUBLESHOOTING YOUR SCROLL SAW.

PROBLEM

 

PROBABLE

CAUSE

Breaking

Blades.

1. Wrong tension.

 

 

2.

Over working

blade.

 

 

3.

Wrong blade application.

 

 

4.

Twisting

blade

in wood,

Motor will

not run.

1.

Defective

cord or plug.

 

 

2.

Defective

motor.

REMEDY SUGGESTED

1, Adjust blade tension.

2.Reduce feed rate.

3, Use narrow blades for cutting thin wood, wide blades for thicker wood.

4. Avoid side pressure on blade.

1, Replace defective parts before using saw again.

2.Consult Sears Service, Any attempt to repair this motor may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at your nearest Sears Store.

.....,, ,,,,,

Vibration

NOTE: There will always be some vibration present when the saw is running because of the motor operation.

Blade Runout--Blade not in-line with arm motion

1.improper mounting of saw.

2.Unsuitable mounting surface.

3.Loose table or table

resting against motor. 4, Loose motor mounting

Blade holders not aligned

1, See mounting instructions in this manual for proper

mounting technique.

2, The heavier your work bench is the less vibration will occur, A plywood workbench will not be as good a work surface as the same size solid lumber. Use

common sense in choosing a mounting surface,

. Tighten table lock knob.

4.Tighten motor mounting screws,

1.Loosen cap screws holding blade hoiders to arms. Adjust position of blade holders--Retighten holders.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Scroll Keep Work Area Clean Know Your Power ToolUSE Recommended Accessories Ground ALL ToolsVingarea AdditionaJ safety instructions for scroll sawContents Unpacking and checking contents Knob Settingthetablefor Horizontal or BevelTional Instructions To Align the Bevel Indicator Adjust the table as necessary for your requirementsTOP of Motorwhich could Cause Noise When 3HE Clockwise Removing and installing bmadesFor Picture Guard Removed Clarity BefOre applying power, use screwdriver in slot at endHoles inframe Quantity Description Mounting the scroll saw toMounting this saw to a workbench a so,lid wood Your scrollsaw Insert Key into switchTension Knob Blade Holder Bevel Ponter13Toturnmachineon,.place finger under switch lever Making Interior Scroll Cuts Switch KEY Before Removing or REPI,CING BladeRemove Always TurnOptionalto be MADEAUX. Byworksawsurfaceuser Mounting AN Auxilliary Work TableFlatwashers FAILURE, Auxilliary Work Surface should not Exceed 24 x 12Alternate Method of Oiling Bearings if RE,OIL Caps are Lost Switch From Power Or LubriInternal parts Recommended Switch BlackGlossary of terms for woodworking Remedy SuggestedBushing 60256 Key Switch Switch & Cord STD Screw, Hex Hd /16 !8 x 7/8Key Part Description = I++ 66055 66047 Coupling, EccentricParts List for Craftsman 16-INCH Motorized Scroll SAW RVlCE

113.23611 specifications

Sears 113.23611 is a versatile portable air compressor that has gained popularity among DIY enthusiasts and professionals due to its robust performance and convenient design. This model showcases features that simplify a variety of tasks, from inflating tires to powering pneumatic tools, making it an essential addition to any toolkit.

One of the standout characteristics of the Sears 113.23611 is its oil-lubricated pump system, which enhances the compressor’s durability and efficiency. This feature not only extends the lifespan of the machine but also ensures quieter operation compared to its oil-free counterparts. The compressor delivers a maximum psi of around 125, providing ample pressure for various applications.

The Sears 113.23611 is equipped with a 3-gallon tank that allows for continuous operation while maintaining a compact profile. Its lightweight design makes it easy to transport and store, appealing to both hobbyists and professionals who require mobility in their work. The compressor also features a quick-connect coupler, which facilitates easy tool changes and reduces downtime during projects.

In terms of technology, the Sears 113.23611 is designed with user-friendly controls. The pressure gauge allows users to monitor the PSI levels accurately, while the on/off switch is conveniently located for quick access. Furthermore, the compressor's continuous duty cycle ensures uninterrupted air supply, making it an excellent choice for extended tasks.

Safety features are also a priority in the design of this air compressor. It includes a thermal overload protector that prevents overheating, a crucial aspect for prolonged usage. The sturdy construction ensures stability during operation, and the rubber feet provide added grip, reducing vibrations and enhancing safety.

Overall, the Sears 113.23611 air compressor stands out for its combination of power, portability, and user-friendly features. It is an ideal solution for those looking to accomplish a range of tasks efficiently, whether it's for home projects, automotive work, or professional applications. With its reliability and solid performance, this compressor remains a favored choice in the world of portable air compressors.
Top Page Image Contents