Sears 113.2945 owner manual Step THREE--INSTALLATION of Front Table

Page 6

 

BOTTOM

SIDE

OF

TABLE

REAR

TABLE

 

 

 

 

SUPPORT

BRACKET

 

 

 

 

FRONT

 

 

 

 

 

 

TABLE

 

 

T-NUT

CORRECTLY

INSTALLED

 

 

 

 

 

 

 

 

 

Q,I

 

LEVELING

SCRTW

 

 

 

 

 

 

TOP OF

TABLE

 

 

 

 

 

T-NUT

 

 

 

 

 

 

 

 

SCREW

BASE

LEVELING

SCREW

(No.

10 x

5/8 IN.)

INSTALLED

 

 

IN T-NUT

Figure 8

3.Loosen keylocking bolts (See figure 7) and insert a 3/16- inch Hex-L wrench into the socket-head set-screw that

adjusts the column tube wedge key, as shown in figure 7. Rotate the set-screw slowly in (clockwise) until no side play can be felt in radial arm.

4.Check for binding by rotating the elevation crank. If the crank rotates with noitceable resistance, loosen the set-

screw by rotating the Hex-L wrench counterclockwise until rotation is normal. An effective method for finaliz-

ing the set-screw adjustment is to rotate the screw while the elevation crank is being rotated, checking for side play in radial arm as the adjustment progresses. The adjustment is correct when all side play of radial arm is eliminated and only very slight additional resistance can be felt when rotating the elevation crank.

5.If some radial arm side play can still be detected after performing the above adjustment, it will be necessary

to adjust the forward five screws through the right-, and left-hand column supports as follows:

a.While rotating the elevation crank, tighten the five column adjusting screws slightly at the forward edge of column supports. Each screw should be tightened only slightly, and each one the same amount, until a slight resistance can be felt when rotating the elevation crank, then each screw backed off just

enough to restore a normal feel to the elevation crank.

b.Recheck the adjustment of the column tube wedge key set-screw as outlined in preceding instructions.

Figure 10

COLUMN

 

 

SUPPORT

HOLE FOR

TABLE

 

HOLD-DOWN

SCREW

 

(SEVEN,TOTAL)

 

R.H. TABLE SUPPORT

 

LEVELING SCREW

FRONT TABLE

HOLE

Figure 9

 

6.After the above adjustments have been completed, re- check the radial arm for absence of side play.

7.When all side play has been eliminated, lock the column tube key in place by tightening keylocking bolts. (See figure 7.)

STEP THREE--INSTALLATION OF FRONT TABLE

1.Place the large (front) table board upside-down on floor. Distinguish between the one through-bored (leveling screw) hole near the center of the board, and the seven counterbore holes. The counterbores are in the top sur- face of the board. Drive the T-nut into the through-hole.

(See figure 8 which shows the T-nut installed.)

2.With the front table board still in the upside-down posi- tion, locate the two pre-drilledscrew holes near each end of the table. Attach the two rear table support brackets to the table with two No. 10 x 5/8-inch screws in each bracket. (See figure 8.)

3.Place the 1/4-20 U-clip nut on the base cross member to receive the center front table attaching screw.

4.Place the large, front table board on the table supports. (See figure 9.)

5.Align the counterbore holes with matching holes in table supports.

6.Place a 17/64-inch plain washer and a 1/4-20 x 1-inch pan-head machine screw from loose parts pack in each of the six counterbore holes located above the table

supports. Use a 1/4-20 x 1-1/4-inch pan-head machine screw in counterbored hole at the center of the table board.

Figure 1 1

ii

Image 6
Contents Assembly Operating Repair Parts Avoid Accidental Starting Remove Adjusting Keys and WrenchesThis Safety Seal Power Tool Institute Assures YOU ForceAssembling and Adjusting Your SAW Unpacking and Checking ContentsAlignment Instructions Motor Safety ProtectionMounting the SAW on a Work Bench Feet Less 100AR or Step TWO--ELIMINATING Radial ARM Side PlayStep THREE--INSTALLATION of Front Table Step FOUR--SQUARING the CROSS-CUT Travel Mark this tooth with crayon or chalkStep FIVE--SQUARING the SAW Blade to Table TOP Step SIX--CHECKING SAW Blade for Heel Left RightIndicator Instructions for USE of KEY and Switch Operating Controls See figureCarriage Bearing Adjustment Yoke Clamp ARM AdjustmentRemoving Radial ARM Side Play Periodically Lubricate These Points ControlsNo Lubrication Required AT These Points DarkCROSS-CUTTING Preliminary CROSS-CUT AT PositionRipping Bevel and Miter CutsRemoval and Installation Manual Brake Assembly USE Dado HeadMolding or Shaping Sanding Routing and DovetailingBoring Helpful HintsFor Trouble Shooting Charts See Pages For Parts Lists IiITrouble RemedyProbable Cause Key Port Parts ListITEM--10-INCH DescriptionSee for Exploded View CRAFTSMAN, l O-INCH Radial ARM SAW, Model No PartKey Part Description X1/32OJ87 CRAFTSMAN, IO-INH RADtAL ARM SAW, Modil No .2945o Key PartCRAFTSMAN, 10-NCH Radial ARM SAW, Model No I3.29o,50 63052Instructions to Operator Sufficient to inflict severe injuryOwners manuaJ