Sears 113.2945 Mounting the SAW on a Work Bench, Alignment Instructions, Motor Safety Protection

Page 4

MOTOR SAFETY PROTECTION

The saw motor is equipped with a manual-reset thermal overload protector, designed to open the power line circuit when the motor temperature exceeds a safe value.

1.If the protector opens the line and stops the saw motor, press the saw switch to the "OFF" position immediately and allow the motor to cool.

2.After cooling to a safe operating temperature, the overload protector can be closed manually by pushing in the red button on the motor cover and nameplate. If

the red button will not snap into place immediately, the motor is still too hot and must be allowed to cool for a

while longer. (An audible click will indicate protector is closed.)

3.As soon as the red button will snap into running position, the saw may be started and operated normally by pressing the saw switch to the "ON" position.

4.Frequent opening of fuses or circuit breakers may result if motor is overloaded, or if the motor circuit is fused with a fuse other than those recommended. Do not use

a fuse of greater capacity without consulting the power company.

5.Although the motor is designed for operation on the voltage and frequency specified on motor nameplate, normal loads will be handled safely on voltages not more than 10% above or below the nameplate voltage. Heavy loads, however, require that voltage at motor terminals be not less than the voltage specified on nameplate.

6.Most motor troubles may be traced to loose or incorrect connections, overloading, reduced input voltage (which results when small size wires are used in the supply circuit) or when the supply circuit is extremely long. Always check connections, load and supply circuit when the motor fails to perform satisfactorily. Check wire sizes and lengths with the table in the next paragraph.

IMPORTANT: The following wire sizes are recommended for connecting the motor to power source for trouble-free operation.

 

Length

of

 

 

Wire

Size

Required

 

Conductor

 

 

(American

Wlre

Gauge No.)

50

feet

or

less

.................

 

No.

12

100

feet

or

less

.................

 

No.

10

100

feet

to

150

feet

No.

8

150

feet

to

200

feet

No.

6

200

feet

to

400

feet

No.

4

For circuits of greater length the wire size must be in-

creased proportionally.

I TABLE SUPPORT

(RIGHT-HAND)

PLAIN WASHER\J

(11/32 INCH)

_L'_

_--TABLE

SUPPORT

_._

"'_

 

 

(LEFT-HAND)

 

_

LOCKWASHER

(5/16

INCH)

SCREW

 

INCH)

 

Figure 2

(HEX-HD, 5/16-1_ _ 3/4

 

 

MOUNTING THE SAW ON A WORK BENCH

The saw should be placed on a suitable sturdy work bench, or Craftsman Power Tool Bench. The base of the saw must

be mounted flush to a flat surface on the work bench to

prevent distortion of the saw base. The nuts, screws, and washers which attach the wooden shipping skids to the saw base may be used to secure the saw base to the work bench, or tool bench.

ALIGNMENT INSTRUCTIONS

NOTE: The seven basic "steps" that follow are essential in order to insure correct saw table

alignment.

WARNING: Make sure the power cord is not plugged into an electrical outlet when working on the saw.

STEP ONE--INSTALLATIONAND ADJUSTMENT

OF TABLE SUPPORTS

1.Place the saw on a work bench or table.

2.Attach right-,and left-hand table supports to the saw base as follows: (See figure "2.)

NOTE: Right-, and left-hand supports may be identified by the three "keyholes" in the table attaching surface of each support. These key- holes are for attaching the table clamps and are located at the rear of the saw. Also, the

angle of each support turns outward, away from the saw base. (See figure 2.)

a. Place one 5/16-inch, split Iockwasher and one 11/32- inch plain washer on each of the four 5/16-18 x 3/4- inch, hex-head screws, all from the loose parts pack.

b. Attach each table support to the saw base with two of the hex-head screws, Iockwashers and plain wash-

ers assembled in preceding step.

c. Position each support on the base so each screw is approximately centered in the slotted hole in the support.

d. Tighten the screws just enough to hold the table supports in position, but loose enough to slip against the base channel when tapped with a plastic mallet.

3.Adjust Table supports parallel to radial arm as follows:

a.Loosen the guard clamp screw and remove the guard.

b.Lock carriage and hold the motor shaft (at inner edge of saw blade) with the shaft wrench and loosen the

ARBOR

WRENCH

SHAFT

Figure 3

Image 4
Contents Assembly Operating Repair Parts Remove Adjusting Keys and Wrenches This Safety Seal Power Tool Institute Assures YOUAvoid Accidental Starting ForceAssembling and Adjusting Your SAW Unpacking and Checking ContentsMotor Safety Protection Mounting the SAW on a Work BenchAlignment Instructions Feet Less 100AR or Step TWO--ELIMINATING Radial ARM Side PlayStep THREE--INSTALLATION of Front Table Step FOUR--SQUARING the CROSS-CUT Travel Mark this tooth with crayon or chalkStep FIVE--SQUARING the SAW Blade to Table TOP Step SIX--CHECKING SAW Blade for Heel Left RightIndicator Instructions for USE of KEY and Switch Operating Controls See figureYoke Clamp ARM Adjustment Carriage Bearing AdjustmentRemoving Radial ARM Side Play Controls No Lubrication Required AT These PointsPeriodically Lubricate These Points DarkCROSS-CUTTING Preliminary CROSS-CUT AT PositionRipping Bevel and Miter CutsUSE Dado Head Removal and Installation Manual Brake AssemblyMolding or Shaping Routing and Dovetailing BoringSanding Helpful HintsFor Trouble Shooting Charts See Pages For Parts Lists IiITrouble RemedyProbable Cause Parts List ITEM--10-INCHKey Port DescriptionSee for Exploded View CRAFTSMAN, l O-INCH Radial ARM SAW, Model No PartKey Part Description X1/32OJ87 CRAFTSMAN, IO-INH RADtAL ARM SAW, Modil No .2945o Key PartCRAFTSMAN, 10-NCH Radial ARM SAW, Model No I3.29o,50 63052Instructions to Operator Sufficient to inflict severe injuryOwners manuaJ