Sears 919.15442 Operating Procedures, Grounding Instr,JcUons, Break-In PrOcums, Adapter

Grounding Instr,JcUons

L_ i

IMPROPER GROUNDING CAN RESULT iN ELECTRICAl. SHOCK. IN THE EVENT OF A

SHORT CIRCUIT, GROUNDING REDUCES IHE RISK OF SHOCK BY PROVIDING AN ESCAPE WIRE FOR THE ELECTRIC CUR- RENT. THIS AIR COMPRESSOR MUST BE

PROPERLYGROUNDED.

1.The air compressorts equippedwlth a cord having a groundingwire with an _ppr_priate groundingplug. The plug must be used with an outletthat has been

installedand groundedin accordance wi_h all IocaI codes and ordinances, The out_et must have the

_aJ'_configurationeas the plug. DO NOT USE AN

ADAPTER,

2, Do not modify the plug 1hathas been provided.!! it does not tit the available outlet, the correct outlet shoutdbe installedby a qualifiederectrician

3inspectthe plugand cordbeforeeach use_Do not use ifthere are signsof damage,

RISK OF ELECTRICAL SHOCK, IF REPAIR- ING OR REPLACING CORD OR PLUG, THE GROUNDING WIRE MUST BE KEPT SEPA-

RATE FROM THE CURRENT.CARRYING WIRES, NEVER CONNECT THE GROUND,

tNG WIRE TO A FLAT BLADE PLUG TER-

MINAL (THE GROUNDING WIRE HAS INSULATION WITH AN OUTER SURFACE

THAT IS GREEN - WiTH OR WITHOUT YEL-

LOW STRIPES.)

if these grounding ine_ru_Uonsare not completely unclerstood0or if In doubtas to whether[he compressor

is properlygrounO_d,havethe install=ioncheckedby a qualifiedelectrlclan_

Ground

"Wire ""

GROUNDING ,,2" L..------J

PIN

120 vOltS,i5 amps

Break-In PrOc_ums

Serious damage moy _glt If _I'KIfoll_ing

break-in tnatructrono =r== not closely followed.

Thisprocedureis only _quir-ud the firstlime the=Jrcom- preSSOriS put intoserwce,

1.Set the swlt_ OFFtAUTO lever to the'OFF' poetriespressure

2Plug the.power c_ordinto the (;orrectbranc;h cimUit receptacJe,

3Turn the regulatorc!ockw'L._opening,e,,it fulIy,to pre. ventmr pressureI:_uz=o-up=nthe tanK,

4_Move *,heOFF!AUTO leverto "AUTO'.Th_ compres- sor wltI starL

5, Run _he compressorfor 10 minutes, Make sure the

rupegulatorIs open and them is no tank pressure build- ,_

6After 10 rnin.utes,_ose t,heregultttor by lurning it counter-c_oc:Kwise,fne _urtankv_lIfill_ OJt-,outpres- sure and lhanthe rno_r Will510p

OPERATING PROCEDURES

1, Before attaching aJrhose or accessories, make sure the OFFtAUTO lever is set to "OFF" and the air regulatorIs closed (Close it by turningit counter- ClOCkWiSe)

2_At_chhOSe _ndaocessorfes.

WARNING

1"OOMUCH AIR PREgSURE CREATES A

HAZARDOUS RISK OF BURSTING, CARE-

FULLYFOLLOW STEPS 3 AND 5 EACH TIME

THE COMPRF-_SOR IS USED.

COMPRESSED AIR FROM THE OUTFIT MAY CONTAIN WATER CONDENSATION. DO NOT SPRAY UNRLTERED AIR AT AN ITEM Tl1AT GOULD B_ DAMAGED. SOM F AIR

OPERATED TOOLS OR DEVICES MAY

REQUIRE FILTERED AIR. READ THE INSTRUCTIONS FOR THE AIR TOOL OR

DEVICE,

. Check the manufacturer's_lmum preserve_ating

for air tools and accessories, "Theregulatoroutlet

pressuremustnever exceed the maximurnprB_$ure

_at]ng.