Sterling BP818, BP814, BP810 manual

Page 37

3.Pivot the in-feed hopper completely back to gain clear access to the cutting chamber, and clear any process material or foreign objects from between the knives.

4.Rotate the rotor so that the rotor knives will not interfere with the removal of the bed knife. Using a wooden block, block the rotor to prevent it from rotating while removing the knives.

5.Loosen the lock nuts and back off the adjustment screws. (See Error! Reference source not found..)

6.Loosen and remove the bed knife shield bolts and remove the shield, positioned above the knife. The remaining bed knife bolts and bed knife may now be removed.

7.Perform the above steps to remove the rear (upstroke) bed knife as well.

NOTE: Before replacing the bed knife with new or sharpened knives, wipe the knife seats on the knife block, being sure to clean off all process material. The tapped holes in the knife block (used for holding the knives in place) should be clear of any dirt, oil, or process material.

8.Install new or sharpened bed knives on each knife seat, making sure that the rotor is blocked to prevent it from rotating while installing each knife. Be sure to place the bed knives in the correct positions⎯the rear (up stroke) bed knife must be placed with the extended cutting edge on the bottom, and the front (down stroke) bed knife should be placed with the cutting edge on the top.

9.Before re-installing the knife bolts, wipe them clean with a lightly oil-damped cloth. Do not leave an oil film on the bolt since lubrication can adversely affect the stress on the bolt when torqued to the specified values. It is recommended that the knife bolts be replaced with each new set of knives. This will reduce the risk of bolt failure due to overstretching. Always use the specified replacement bolts.

10.Tighten the bolts that hold just the bed knife, enough to keep the knife in place, while still allowing the adjusting screws to move the knife forward.

11.Adjust the knife gaps with the rotor knives, following Steps 8- 12 in Section 6-4.

12.Replace the shields in position above the bed knives. The shield on the front (down stroke) bed knife should be positioned so that the inside edge is set back approximately 1/32” from the cutting edge below it. Replace the remaining bolts and torque.

Page 37 of 54

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Page Page Page Page Page Start Up and Operation Page Viii Safety Guidelines Safety ConsiderationsPage Guidelines for Moving the Granulator Safety ProceduresClearing a Jammed Cutting Chamber Safety Features Fitted On the Granulator Safety FeaturesOpening the Granulator Safety SwitchWear protective gloves when exposed to knives Introduction Using This ManualTechnical Data Safety Symbols Used in This ManualDescription Optional Equipment Main Components of Standard GranulatorsPage Event of Shipping Damage Unpacking and InspectionIf the Shipment is Not Complete Page Especially the Hopper Positioning the Granulator LiftingInserting the Bin Electrical ConnectionChecking the Cutting Chamber Start-Up ChecksUnscrew the screw knob, and carefully lower the screen. See Licensed Electrician must carry out this operation Checking Rotation DirectionChecking Knife Position Test the Interlock SwitchChecking the Knife Gap Start Up and Operation Pre-Operational ChecklistNever push material into the hopper with hands OperationGeneral Recommendations 6MaintenanceDrive Belt Tension Monthly Maintenance OperationsProper Belt Tension Belt Replacement Removal and Replacement of the ScreenRemoving the Screen Inspection and Adjustment of KnivesPage Inspection of Knives Removing and Replacing Bed KnivesPage Removal and Replacement of Rotating Blades Specifications for Re-sharpening Bed Knives Page General Problems 7TroubleshootingProblem Possible Causes Possible Remedies Electrical Problems Page Drawing CA039060S2 Drawing CA039060S1 Drawing CA039060S3 Drawing CA039060S4 Typical Wiring Diagram Drawing D05991100000 Page Service Notes

BP810, BP818, BP814 specifications

The Sterling BP810, BP818, and BP814 are three cutting-edge devices designed to enhance the user experience in various applications. Each model comes equipped with distinct features, technologies, and characteristics that cater to different needs, making them versatile options for consumers.

The Sterling BP810 is known for its sleek design and user-friendly interface. One of its standout features is the high-resolution display that ensures clear visibility in various lighting conditions. The device operates on a robust operating system, offering seamless performance and multitasking capabilities. With built-in connectivity options, including Wi-Fi and Bluetooth, users can easily sync their devices and access a wide range of applications. The BP810 also boasts impressive battery life, allowing for extended use without frequent recharging.

Moving on to the Sterling BP818, this model takes innovation to the next level with its advanced processing capabilities. Powered by a high-performance processor, the BP818 delivers lightning-fast response times, making it an excellent choice for demanding tasks. Its enhanced graphics performance is perfect for gaming and multimedia applications, providing users with an immersive experience. The device also features an upgraded camera system, enabling high-quality photography and video recording, which is ideal for content creators. Additionally, the BP818 incorporates state-of-the-art security features, including facial recognition and fingerprint scanning, ensuring that user data remains protected.

Lastly, the Sterling BP814 focuses on durability and functionality. This device is built to withstand harsh conditions, making it suitable for outdoor use and professional environments. Its rugged design doesn't compromise on aesthetics, as it combines style with strength. The BP814 includes a range of practical features, such as customizable buttons for quick access to frequently used applications. This model is also equipped with advanced sound technology, delivering crystal-clear audio for both calls and media playback. Furthermore, the battery technology in the BP814 is designed for efficiency, allowing users to maximize productivity throughout the day.

In summary, the Sterling BP810, BP818, and BP814 each present unique strengths that cater to different user preferences. Whether you need a device for casual use, intensive tasks, or rugged environments, there is a Sterling model tailored to meet those requirements. With advancements in processing, connectivity, and security, these devices exemplify Sterling's commitment to providing top-tier technology and user satisfaction.
Top Page Image Contents