Sterling BP810, BP814, BP818 manual Removal and Replacement of Rotating Blades

Page 38

13. Close the machine, following Steps 12-14in Section 6-4.

6-6 Removal and Replacement of Rotating Blades

NOTE: A qualified operator / maintenance mechanic should perform this operation. Protective gloves must be worn to avoid injury when handling the cutting knives.

To remove and replace rotor knives, complete the following procedure:

1.Open the granulator by following Steps 1-0in Section 6-3.

2.Open the rear-closing panel by releasing the locking latch.

3.Pivot the in-feed hopper completely back to gain clear access to the cutting chamber, and clear any process material or foreign objects from between the knives.

4.Rotate the rotor so that the knife bolts are in a convenient position to remove the bolts with the appropriate wrench. Using a wooden block, block the rotor to prevent it from rotating while removing knives or after a knife has been removed.

5.Loosen and remove the knife bolts and lift the knife off the knife seat removing it from the cutting chamber.

6.Perform the above steps until all the rotor knives are removed.

NOTE: Before replacing the rotor knife with new or sharpened knives, wipe the knife seats on the rotor, being sure to clean off all process material. The tapped holes in the rotor (used for holding the knives in place) should be clear of any dirt, oil, or process material.

7.Loosen the bed knife bolts and adjusting screws, and pull back the bed knife so that the rotor knives will collide as they are installed and rotated.

8.Install new or sharpened knives on each knife seat, making sure that the rotor is still blocked to prevent it from rotating while installing each knife.

9.Before re-installing the knife bolts, wipe them clean with a lightly oil-damped cloth. Do not leave an oil film on the bolt since lubrication can adversely affect the stress on the bolt when torqued to the specified values. It is recommended that the knife bolts be replaced with each new set of knives. This will reduce the risk of bolt failure due to overstretching. Always use the specified replacement bolts.

Page 38 of 54

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Page Page Page Page Page Start Up and Operation Page Viii Safety Considerations Safety GuidelinesPage Clearing a Jammed Cutting Chamber Safety ProceduresGuidelines for Moving the Granulator Safety Features Safety Features Fitted On the GranulatorSafety Switch Opening the GranulatorWear protective gloves when exposed to knives Using This Manual IntroductionDescription Safety Symbols Used in This ManualTechnical Data Main Components of Standard Granulators Optional EquipmentPage If the Shipment is Not Complete Unpacking and InspectionEvent of Shipping Damage Page Especially the Hopper Lifting Positioning the GranulatorElectrical Connection Inserting the BinStart-Up Checks Checking the Cutting ChamberUnscrew the screw knob, and carefully lower the screen. See Checking Rotation Direction Licensed Electrician must carry out this operationTest the Interlock Switch Checking Knife PositionChecking the Knife Gap Pre-Operational Checklist Start Up and OperationOperation Never push material into the hopper with hands6Maintenance General RecommendationsProper Belt Tension Monthly Maintenance OperationsDrive Belt Tension Removal and Replacement of the Screen Belt ReplacementInspection and Adjustment of Knives Removing the ScreenPage Removing and Replacing Bed Knives Inspection of KnivesPage Removal and Replacement of Rotating Blades Specifications for Re-sharpening Bed Knives Page 7Troubleshooting General ProblemsProblem Possible Causes Possible Remedies Electrical Problems Page Drawing CA039060S2 Drawing CA039060S1 Drawing CA039060S3 Drawing CA039060S4 Typical Wiring Diagram Drawing D05991100000 Page Service Notes

BP810, BP818, BP814 specifications

The Sterling BP810, BP818, and BP814 are three cutting-edge devices designed to enhance the user experience in various applications. Each model comes equipped with distinct features, technologies, and characteristics that cater to different needs, making them versatile options for consumers.

The Sterling BP810 is known for its sleek design and user-friendly interface. One of its standout features is the high-resolution display that ensures clear visibility in various lighting conditions. The device operates on a robust operating system, offering seamless performance and multitasking capabilities. With built-in connectivity options, including Wi-Fi and Bluetooth, users can easily sync their devices and access a wide range of applications. The BP810 also boasts impressive battery life, allowing for extended use without frequent recharging.

Moving on to the Sterling BP818, this model takes innovation to the next level with its advanced processing capabilities. Powered by a high-performance processor, the BP818 delivers lightning-fast response times, making it an excellent choice for demanding tasks. Its enhanced graphics performance is perfect for gaming and multimedia applications, providing users with an immersive experience. The device also features an upgraded camera system, enabling high-quality photography and video recording, which is ideal for content creators. Additionally, the BP818 incorporates state-of-the-art security features, including facial recognition and fingerprint scanning, ensuring that user data remains protected.

Lastly, the Sterling BP814 focuses on durability and functionality. This device is built to withstand harsh conditions, making it suitable for outdoor use and professional environments. Its rugged design doesn't compromise on aesthetics, as it combines style with strength. The BP814 includes a range of practical features, such as customizable buttons for quick access to frequently used applications. This model is also equipped with advanced sound technology, delivering crystal-clear audio for both calls and media playback. Furthermore, the battery technology in the BP814 is designed for efficiency, allowing users to maximize productivity throughout the day.

In summary, the Sterling BP810, BP818, and BP814 each present unique strengths that cater to different user preferences. Whether you need a device for casual use, intensive tasks, or rugged environments, there is a Sterling model tailored to meet those requirements. With advancements in processing, connectivity, and security, these devices exemplify Sterling's commitment to providing top-tier technology and user satisfaction.
Top Page Image Contents