Hobart Welding Products OM-493 manual Servicing Air Cleaner, Overload Protection, Stop engine

Page 26

7-3. Servicing Air Cleaner

 

 

Y

Stop engine.

 

1

Y Do not run engine without air

 

 

 

cleaner or with dirty element.

 

 

1

Wrapper (Foam Element)

2

Wash wrapper with soap and water solution. Allow wrapper to air dry completely.

Spread 1 tablespoon SAE 30 oil evenly into wrapper. Squeeze out excess oil.

2 Element

Replace element if dirty, oily, or damaged.

aircleaner3 1/97 – ST-156 852 / Ref. ST-192 519-A / S-0759

7-4. Overload Protection

1

Tools Needed:

3/8 in

YStop engine. Disconnect negative (–) battery cable.

1 Fuse F1 (See Parts List)

F1 protects the exciter excitation winding from overload. If F1 opens, there is no/low weld and auxiliary power output.

2 Fuse F6 (See Parts List)

F6 protects the engine wiring sys- tem from overload. If F6 opens, engine will not crank.

Replace any open fuses. Reinstall cover before operating.

.When a fuse opens, it usually

indicates a more serious prob- lem exists. Contact a Factory Authorized Service Agent.

2

Ref. ST-802 213-B / Ref. ST-192 519-A

OM-493 Page 22

Image 26
Contents Description OM-493Processes From Hobart to You Table of Contents Page Electric Shock can kill Symbol UsageArc Welding Hazards ARC Rays can burn eyes and skinEngine Hazards Engine Exhaust Gases can kill Battery Explosion can BlindMoving Parts can cause injury Engine Heat can cause fireRadiation can cause interference Principal Safety StandardsEMF Information ARC Welding can cause interferenceUN Choc Électrique peut tuer Signification des symbolesConsignes DE Sécurité Lire Avant Utilisation LES Fumées ET LES GAZ peuvent être dangereuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer un in- cendie ou une explosionDES Particules Volantes peuvent blesser les yeux LE Bruit peut affecter l’ouïeLA Chaleur DU Moteur peut pro- voquer un incendie DES Organes Mobiles peuvent provoquer des blessures’EXPLOSION DE LA Batterie peut LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécuritéInformation sur les champs électromagnétiques Consignes relatives aux stimulateurs cardiaquesWeld, Power, and Engine Specifications SpecificationsSymbol Definitions DefinitionsDimensions Dimensions, Weights, and Operating AnglesAuxiliary Power Curve Duty Cycle Exceeding duty cycle can damage unit and void warrantyFuel Consumption Continuous WeldingVolt-Ampere Curve InstallationInstalling Welding Generator Movement Do not lift unit from end Airflow ClearanceEngine Prestart Checks FuelRead and follow all instruc Activating The Dry Charge Battery If ApplicableDo not overfill battery cells ChargerTools Needed 1/2 Connecting the BatteryInstalling Exhaust Pipe Connect negative cable last100 ft 30 m Or Less Connecting to Weld Output TerminalsSelecting Weld Cable Sizes 10 100% Duty CycleOperating the Welding Generator Engine Control SwitchDo not switch under load Front Panel ControlsWeld Current Operating Auxiliary EquipmentStandard Receptacles 120V 240VGfci Receptacle Option Optional Auxiliary Power ReceptaclesGenerator 120 V 20 a AC Gfci RecepMaintenance Maintenance Label Overload Protection Servicing Air CleanerStop engine. Disconnect negative battery cable Stop engineStop engine and let cool Changing Engine Oil, Oil Filter, and Fuel FilterFull Tools Needed Oil Drain Valve 2 ID x 12 in Hose Oil FilterWeld/Power Speed Adjustment Adjusting Engine SpeedIdle Speed Adjustment Servicing Optional Spark Arrestor Welding TroubleshootingAuxiliary Power Trouble RemedySwitch S2, and throttle solenoid TS1 EngineElectrical Diagram Circuit Diagram For Welding GeneratorGrounding Generator To Truck Or Trailer Frame Auxiliary Power GuidelinesSelecting Equipment Earth ground if supplying Grounding When Supplying Building SystemsHow Much Power Does Equipment Require? Amperes x Volts = WattsIndustrial Motors Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running WattsSingle-Phase Induction Motor Starting Requirements Power Required To Start MotorHow Much Power Can Generator Supply? KVA/HP x HP xTypical Connections To Supply Standby Power 240 120 GroundSelecting Extension Cord Use Shortest Cord Possible Current Load Watts AmperesStick Welding Smaw Guidelines Stick Welding ProcedureWeld current starts when electrode touches work- piece Striking an Arc Tapping Technique Electrode and Amperage Selection ChartStriking an Arc Scratch Start Technique Positioning Electrode Holder Poor Weld Bead CharacteristicsGood Weld Bead Characteristics 10-30 9090 End View of Work AngleConditions That Affect Weld Bead Shape Electrode Movement During WeldingTee Joint Butt JointsLap Joint 16 in 1.6 mm Tack WeldsWeld Test Troubleshooting PorosityTroubleshooting Excessive Spatter Possible Causes Corrective ActionsTroubleshooting Excessive Penetration Troubleshooting Incomplete FusionTroubleshooting Lack Of Penetration Troubleshooting Distortion Troubleshooting Burn-ThroughTroubleshooting Waviness Of Bead Parts List 12-3Dia Part Description Mkgs Quantity Panel, Front w/Components Panel, Front w/Components -1 Item Generator -1 Item Page Page Service SupportCall Contact your Distributor forHobart Welding Products