
least the minimum wire size required.
(See Table A.)
4.If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Table A.)
5.If you are using an extension cord outdoors, make sure it is marked with the suffix
6.Make sure the extension cord is prop- erly wired and in good electrical con- dition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it.
7.Protect the extension cords from sharp objects, excessive heat, and damp or wet areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
(120/240 VOLT)
NAMEPLATE | EXTENSION CORD | ||||||
| LENGTH |
| |||||
AMPERES |
|
| |||||
25’ | 50’ | 75’ | 100’ | 150’ | |||
(at full load) | |||||||
|
|
|
|
| |||
|
|
|
|
|
| ||
0 – 2.0 | 18 | 18 | 18 | 18 | 16 | ||
2.1 | – 3.4 | 18 | 18 | 18 | 16 | 14 | |
3.5 | – 5.0 | 18 | 18 | 16 | 14 | 12 | |
5.1 | – 7.0 | 18 | 16 | 14 | 12 | 12 | |
7.1 – 12.0 | 18 | 14 | 12 | 10 | - | ||
12.1 | – 16.0 | 14 | 12 | 10 | - | - | |
16.1 | – 20.0 | 12 | 10 | - | - | - | |
TABLE A | * Based on limiting the line | ||||||
voltage drop to five volts at |
150% of the rated amperes.
Symbology
Double Insulated
| Canadian Standards Association |
|
|
| Underwriters Laboratories, Inc. |
|
|
V~ | Volts Alternating Current |
A | Amperes |
| |
|
|
n0 xxxx/min. | No Load Revolutions per Minute |
(RPM) |
Specifications
Electrical | 120 V~ / 60 Hz | |
Power Cord: 18 AWG X 3C | ||
Requirements | ||
9.6 No Load Amps | ||
| ||
Lathe Type | Wood Cutting | |
|
| |
Motor | 1.0 HP | |
|
| |
Motor Speed | 1720 RPM | |
|
| |
Spindle Speeds | 670, 840, 1040, 1230, 1480, 1650, 1770, | |
(RPM) | 2100, 2420, 2900 | |
Spindle Taper | ||
|
| |
Spindle Thread | 1” Diameter x 8 TPI x 7/8” Long | |
|
| |
Headstock | Rotates at 0°, 60°, 90°, 120°, 180° | |
Adjustments | ||
| ||
Tail Stock | ||
Quill Travel | ||
| ||
Tail Stock | ||
Quill Taper | ||
| ||
Tool Rest Travel | ||
|
| |
Swing Over Bed | ||
|
| |
Drive Method | Belt & Pulley | |
|
| |
Belt Type | ||
|
| |
| 3mm, 4mm, 6mm Hex Wrenches (1 ea.) | |
Accessories | Dead Center (Qty. 1) | |
Faceplate (Qty. 1) | ||
| ||
| Flat Wrenches (Qty. 2) | |
Net Weight | 282.2 Pounds | |
|
|
SKU 98676 | For technical questions, please call | Page 8 |