Jet Tools JWBS-20QT, JWBS-18QT, 20QT-5, 20QT-3 Lower Bearing Adjustments, Guide Gearings Adjustment

Page 18

Lower Bearing Adjustments

Unplug the machine from power source before making any adjustments! Blade teeth are sharp - use care when working near the saw blade. Failure to comply may cause serious injury.

Note: Blade tension and tracking must be properly adjusted prior to bearing guide setup. Refer to the Blade Tension section (page 16).

1.Place the mode selection lever (J, Fig. 18) in the Full Tension position.

Referring to Figure 23:

2. Loosen the thumb screw (B).

This will allow the thrust bearing (A) to move freely and prevent interference with the saw blade (C) during the following steps.

Guide Gearings Adjustment

3.Loosen the locking handle (D) then turn the adjustment screw (E) to adjust the assembly forward or backward until the front of the guide bearings (F) rest just behind the gullet of the blade teeth (C and inset).

4.Tighten the locking handle (D).

Thrust Bearing Adjustment

5.With the thumb screw still loose (from Step 1), slide the thrust bearing and bearing post until the space between the bearing (A) and the back edge of the blade (C) is approximately 1/64”.

A convenient way to achieve this spacing is by placing a dollar bill folded twice (four thicknesses) between the blade and support bearing – four thicknesses of a dollar bill is approximately 1/64”.

6.Tighten the thumb screw (B).

7.Loosen the lock knob (G). Rotate the adjustment handles (H) until the guide bearings

(F)rest lightly against the blade (C). Do not force the guide bearings against the side of the blade.

8.Tighten the lock knob (G).

Check to make sure the adjustments have not changed and the bearing guides do not pinch the blade.

Figure 23

Place the mode selection lever (J, Fig. 18) in the Partial Tension position when the machine is not in use.

18

Image 18
Contents Inch, 20-Inch Band Saw Warranty and Service Warranty PeriodTable of Contents Page Page Introduction Specifications JWBS-18QT-3 JWBS-20QT-3Grounding Instructions Model JWBS-18QTModels JWBS-18-3, -20QT-3, -20QT-5 Circuit InformationContents of Shipping Container UnpackingMounting the Table AssemblyHandwheel For band saw model JWBS-18QTRail Assembly Fence Assembly and AdjustmentAssembling the Fence to Fence Body Fence Adjustment Adjusting Clearance between Fence and Table Resaw GuideMiter Gauge Loosen the lock knobs/lock handle G AdjustmentsAdjusting 90 Degree Table Stop Tighten the lock knobs/lock handleInstalling/Changing Blades Blade Tension HandwheelBlade Tension Blade TrackingOverview Bearing Adjustments Upper Bearing AdjustmentsLower Bearing Adjustments Guide Gearings AdjustmentThrust Bearing Adjustment Blade Lead Motor C Changing the Blade SpeedBelt Tension Handle aReplacing the Poly V-Belt Pulley Alignment Return to of the Replacing Poly V-BeltStart/Stop Switch Operating ControlsBrake Pedal JWBS-20QT only Ripping General ProcedureOperation CrosscuttingResawing Saw Blade SelectionMaintenance Blade BreakageBlade Selection Guide Troubleshooting TroubleReplacement Parts PartsUpper Wheel Assembly 18QT Index No. Part No Description Size QtyTS-1533052 Lower Wheel and Motor Assembly 18QT JWBS18X-MFC#10-24 Blade Guide Assembly 18QT JWBS18DX-359 Table and Fence Assembly 18QT JWBS18-MGCP Upper Wheel Assembly 20QT JWBS18DXA-164 Lower Wheel and Motor Assembly 20QT #10-24x1-1/2 TS-069204 Lower Wheel and Motor Assembly 20QT Blade Guide Assembly 20QT 20x1/4 JWBS18DX-365 Blade Guide Assembly Upper Bearing Guide Lower Bearing GuideTable and Fence Assembly 20QT JWBS20QT-FCPTS-0051091 Hex Cap Screw Electrical Connections 4 HP, 1PhMagnetic Switch HP, 1PhElectrical Board Band Saw Model No. JWBS-20QT-5 SN 708755B New Sanford Road LaVergne, TN 37086-4184, USA Phone

JWBS-20QT, 18QT-3, JWBS-18QT, 20QT-5, 20QT-3 specifications

Jet Tools has long been recognized as a reliable name in the woodworking and metalworking industries, offering a variety of high-quality tools tailored for both professional craftsmen and enthusiastic hobbyists. Among their product range, the Jet Tools 20QT-3, 20QT-5, JWBS-18QT, 18QT-3, and JWBS-20QT stand out due to their innovative features, technologies, and stellar performance.

The Jet Tools 20QT-3 and 20QT-5 are notable for their robust cast iron construction, ensuring stability and durability while handling heavy workloads. The 20QT-3 model comes equipped with a powerful 2 HP motor, providing ample performance for a variety of applications. It also features a versatile tilting blade system allowing precise angles for your cuts. Meanwhile, the 20QT-5 offers an enhanced motor capacity, boasting a 3 HP motor, further increasing its efficiency and capability in demanding tasks. Both models feature a large capacity of 20 quarts, ideal for extended projects where consistent performance is key.

The JWBS-18QT is another gemstone in Jet's lineup, designed specifically for woodworkers needing precision and control. With an 18-inch throat capacity, it accommodates larger workpieces with ease. Its heavy-duty construction minimizes vibration, leading to more accurate cuts. The JWBS-18QT incorporates Jet’s exclusive blade tracking technology, which ensures optimal blade alignment and reduces wear, improving the lifespan of the blade.

In addition to the 18QT, Jet offers an enhanced version, the JWBS-20QT. This model boasts a superior throat depth of 20 inches, allowing even more versatility for larger projects. It includes advanced features like an easy-to-use quick-release blade tension, making blade changes faster and more convenient, and an integrated dust collection port that helps to keep your workspace clean and free of debris.

The 18QT-3 model focuses on performance in a compact package, providing portability without sacrificing quality. It incorporates a sturdy base and adjustable height settings that allow it to adapt to various work environments, making it an excellent choice for smaller workshops or job sites.

In summary, the Jet Tools 20QT-3, 20QT-5, JWBS-18QT, 18QT-3, and JWBS-20QT represent the pinnacle of woodworking machinery. Their combination of durability, advanced technology, and user-friendly features make them ideal for both professionals and serious enthusiasts looking to achieve exceptional results. With Jet Tools, you can be assured of high performance and reliability in every project.