Jet Tools 18QT-3, JWBS-18QT, 20QT-5, 20QT-3, JWBS-20QT operating instructions

Page 4

1.Read and understand the entire owner's manual before attempting assembly or operation.

2.Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3.Replace the warning labels if they become obscured or removed.

4.This band saw is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a band saw, do not use until proper training and knowledge have been obtained.

5.Do not use this band saw for other than its intended use. If used for other purposes, JET disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6.Always wear approved safety glasses/face shields while using this band saw. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

7.Before operating this band saw, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8.Wear ear protectors (plugs or muffs) during extended periods of operation.

9.Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead based paint.

•Crystalline silica from bricks, cement and other masonry products.

•Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

10.Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11.Make certain the switch is in the OFF position before connecting the machine to the power supply.

12.Make certain the machine is properly grounded.

13.Make all machine adjustments or maintenance with the machine unplugged from the power source.

14.Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

15.Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately.

16.Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

17.Provide for adequate space surrounding work area and non-glare, overhead lighting.

18.Keep the floor around the machine clean and free of scrap material, oil and grease.

19.Keep visitors a safe distance from the work area. Keep children away.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Inch, 20-Inch Band Saw Warranty and Service Warranty PeriodTable of Contents Page Page Introduction Specifications JWBS-18QT-3 JWBS-20QT-3Grounding Instructions Model JWBS-18QTModels JWBS-18-3, -20QT-3, -20QT-5 Circuit InformationContents of Shipping Container UnpackingAssembly HandwheelMounting the Table For band saw model JWBS-18QTFence Assembly and Adjustment Rail AssemblyAssembling the Fence to Fence Body Fence Adjustment Resaw Guide Adjusting Clearance between Fence and TableMiter Gauge Adjustments Adjusting 90 Degree Table StopLoosen the lock knobs/lock handle G Tighten the lock knobs/lock handleInstalling/Changing Blades Blade Tension HandwheelBlade Tension Blade TrackingOverview Bearing Adjustments Upper Bearing AdjustmentsGuide Gearings Adjustment Lower Bearing AdjustmentsThrust Bearing Adjustment Blade Lead Changing the Blade Speed Belt TensionMotor C Handle aReplacing the Poly V-Belt Pulley Alignment Return to of the Replacing Poly V-BeltOperating Controls Start/Stop SwitchBrake Pedal JWBS-20QT only General Procedure OperationRipping CrosscuttingResawing Saw Blade SelectionMaintenance Blade BreakageBlade Selection Guide Troubleshooting TroubleReplacement Parts PartsUpper Wheel Assembly 18QT Index No. Part No Description Size QtyTS-1533052 Lower Wheel and Motor Assembly 18QT JWBS18X-MFC#10-24 Blade Guide Assembly 18QT JWBS18DX-359 Table and Fence Assembly 18QT JWBS18-MGCP Upper Wheel Assembly 20QT JWBS18DXA-164 Lower Wheel and Motor Assembly 20QT #10-24x1-1/2 TS-069204 Lower Wheel and Motor Assembly 20QT Blade Guide Assembly 20QT 20x1/4 JWBS18DX-365 Blade Guide Assembly Upper Bearing Guide Lower Bearing GuideTable and Fence Assembly 20QT JWBS20QT-FCPTS-0051091 Hex Cap Screw Electrical Connections 4 HP, 1PhMagnetic Switch HP, 1PhElectrical Board Band Saw Model No. JWBS-20QT-5 SN 708755B New Sanford Road LaVergne, TN 37086-4184, USA Phone

JWBS-20QT, 18QT-3, JWBS-18QT, 20QT-5, 20QT-3 specifications

Jet Tools has long been recognized as a reliable name in the woodworking and metalworking industries, offering a variety of high-quality tools tailored for both professional craftsmen and enthusiastic hobbyists. Among their product range, the Jet Tools 20QT-3, 20QT-5, JWBS-18QT, 18QT-3, and JWBS-20QT stand out due to their innovative features, technologies, and stellar performance.

The Jet Tools 20QT-3 and 20QT-5 are notable for their robust cast iron construction, ensuring stability and durability while handling heavy workloads. The 20QT-3 model comes equipped with a powerful 2 HP motor, providing ample performance for a variety of applications. It also features a versatile tilting blade system allowing precise angles for your cuts. Meanwhile, the 20QT-5 offers an enhanced motor capacity, boasting a 3 HP motor, further increasing its efficiency and capability in demanding tasks. Both models feature a large capacity of 20 quarts, ideal for extended projects where consistent performance is key.

The JWBS-18QT is another gemstone in Jet's lineup, designed specifically for woodworkers needing precision and control. With an 18-inch throat capacity, it accommodates larger workpieces with ease. Its heavy-duty construction minimizes vibration, leading to more accurate cuts. The JWBS-18QT incorporates Jet’s exclusive blade tracking technology, which ensures optimal blade alignment and reduces wear, improving the lifespan of the blade.

In addition to the 18QT, Jet offers an enhanced version, the JWBS-20QT. This model boasts a superior throat depth of 20 inches, allowing even more versatility for larger projects. It includes advanced features like an easy-to-use quick-release blade tension, making blade changes faster and more convenient, and an integrated dust collection port that helps to keep your workspace clean and free of debris.

The 18QT-3 model focuses on performance in a compact package, providing portability without sacrificing quality. It incorporates a sturdy base and adjustable height settings that allow it to adapt to various work environments, making it an excellent choice for smaller workshops or job sites.

In summary, the Jet Tools 20QT-3, 20QT-5, JWBS-18QT, 18QT-3, and JWBS-20QT represent the pinnacle of woodworking machinery. Their combination of durability, advanced technology, and user-friendly features make them ideal for both professionals and serious enthusiasts looking to achieve exceptional results. With Jet Tools, you can be assured of high performance and reliability in every project.
Top Page Image Contents