Jet Tools J-7020, J-7040 operating instructions Parts List Base, Part Description QTY

Page 22

22

Parts List - Base

	ITEM	PART
	NO.	NO.	DESCRIPTION	QTY
	1	J-5712251	Foot, Left	1
	2	J-5712261	Foot, Right	1
	3	J-5712271	Coolant Reservoir	1
	3-1	5519485	Stopper (PT 3/8")	1
	4		Coolant Pump	1
		J-5712281	115/220, 1-Phase
		J-5712921A	220/440, 3-Phase
	4-1	5519486	Adapter (PT 3/8")	1
	5	5712291	Pan Head Screw	2
			(1/4" x 5/8 “)
	7A	5512101	Filter Screen w/Screw	1
	8	5712331	Hose (5/16")	1
	8-1	5519487	Hose Clamp	6
	9	5712341	Chip Pan	1
	10	J-5712351	Pump Bracket	1
	11	J-5712361	Work Table	1
	11-1	5519491	Label, Made in Taiwan	1
	11-2	5519492	Rivet(2mm)	14
	11-3	TS-1482011	Hex Cap Screw (M6x 10)	1
	11-4	TS-1550041	Washer (M6)	1
	11-5	TS-2361061	Spring Washer (M6)	1
	12	5712371	Screw (1/4" x 7/8")	1
	13	5712381	Hex Cap Screw (1/2" x 1")	4
	13-1	5712391	Spring Washer (1/2")	4
	14	5712641	Washer (1/2")	4
	15	J-5712411	Electrical Control Box	1
	15-1	5519488	Hex Cap Screw	3
			(5/16" x 3/4")
	15-2	TS-0720081	Spring Washer (5/16")	3
	15-3	TS-0680031	Washer (5/16")	3
	15-4	5519501	Label, Pump Switch	1
	16	5712421	Work Stop Bracket	1
	17	5712431	Work Stop Rod	1
	18	5712441	Locking Screw	1
	19	5712451	Screw (1/2")	1
	20	J-5712461	Pump Cover	1
	21	5712471	Hand Wheel Assembly	1

ITEM	PART
NO.	NO.	DESCRIPTION	QTY
21-1	5519494	Set Screw (5/16"x1/2")	1
22	J-5712481	Lead Screw Bracket	1
23	5712491	Screw (5/16" x 1/4")	2
23-1	TS-0720081	Spring Washer (5/16")	2
23-2	TS-0680031	Washer (5/16")	2
24	5712511	Vise Lead Screw	1
24-1	5519710	Key (5x5x20mm)	1
24A	5514806	Collar with Pin	1
25	5712521	Lead Screw Bracket	1
26	5712531	Acme Nut	1
27	5712541	Button	1
28	5712551	Retainer	2
29	5712561	Screw (M5 x 8)	1
30	5712571	Needle Bearing (CB3020)	2
30-1	5519495	Bush (4mm)	1
30-2	5519496	Bush (2mm)	1
31	5712581	Washer (1/2")	2
32	5712591	Pivot Shaft	1
33	J-5712611	Pivot Bracket	1
34	5712621	Screw (1/2" x 3/4")	2
35	5712631	Retaining Ring (S12)	1
36	5712641	Washer (1/2")	2
37	5712651	Spring Pull Pivot	1
39	5712671	Screw (5/8" x 1")	2
40	5712681	Regulating Seat	1
40-1	TS-0051021	Hex Cap Screw	2
		(5/16" x 5/8")
40-2	TS-0720081	Spring Washer (5/16")	2
40-3	TS-0680031	Washer (5/16")	2
41	5712691	Nut (3/8")	1
42	5712711	Screw (3/8"x 1")	1
43	5712721	Protractor Stop Block	1
44	5712731	Screw (M6 x 12)	4
45	5712741	Limit Switch	1
46	5712751	Limit Switch Bracket	1

*For Saw Serial No. 704018 and Earlier

**For Saw Serial No. 704018 and Later

***Spring Changed since Dec. '96

Image 22

Contents Inch x 16-Inch Horizontal Band Saw Life Table of Contents General Specifications SpecificationsMachinery General Safety Warnings When Setting up MachineSafety Instructions on Sawing Systems General Electrical CautionsOperating Instructions Setting Blade SpeedIntroduction ControlsEvaluating Cutting Efficiency Raising/Lowering the Saw HeadControlling the Cut Hydraulic Feed Control Blade SelectionAdjusting the Vise for Angle Cuts Work SetupBlade Break-in Procedures Securing the Workpiece for Square CutsInstallation and Adjustment of Work Stop Starting the SawFactory or Field Procedure AdjustmentsBlade Tracking Adjustment Coolant FlowBlade Guide Bearing Adjustment Checking blade-to-wheel clearance using paper stripsAdjustment of the Limit Switch MaintenanceTest Cutting to Verify Adjustment Accuracy CleaningChanging the Drive Belt Adjusting the Counterbalance SpringChanging Blades Replacing the Drive MotorReplacing the Drive Wheel Adjusting the Blade GuidesReplacement of Carbide Blade Guide Replacing Idler Wheel or Idler BearingReplacement of Blade Edge Bearings Machine SetupReplacement of Guide Bearings Replacement of the Wire BrushModel J-7020 cut-off saw wiring diagram ElectricalModel 7040 cut-off saw wiring diagram Troubleshooting Fault Probable cause Suggested remedyReplacement Parts WMH Tool Group, IncExploded View Base Parts List Base Part Description QTY46-1 194 5713251 Screw 1/4 x 3/8 195 Exploded View Head Parts List Head TS-0720081 Part Description QTY Page Page