Chicago Electric 61971 Using the Workpiece Extension Supports, Adjusting the Miter Angle

Page 11

Using the Workpiece Extension Supports

1.The Table Extensions are inserted into each side of the Base, and locked in place using the Wing Screws.

2.When properly installed, the upper face of the Table Extensions are level with the Table, and provide a wider support surface for the workpiece.

3.Support the workpiece to be level with the Table, and so that after the cut is made the cut off pieces will not fall. Use sawhorses or other supports (not included) to support longer workpieces.

4.If the workpiece is not level, an unintentional bevel cut will be made in the material. If the workpiece is not supported, it will bind the blade and may cause the material to kick back, potentially causing injury.

Safety

Adjusting the Miter Angle

A miter cut is one that is at an angle across the horizontal surface of the material. 45º miter cuts to join two pieces in a right angle corner are common. A 30º cut is often used for a scarf joint or to make a chamfered end.

1.Loosen the Miter Knob by turning it approximately 2 turns counterclockwise.

2.Press down the Miter Lock to unlock the Table. While holding the Miter Lock down,

move the Table to the desired angle.

3.The Miter Angle Indicator will indicate the selected angle. While the Miter Lock is released, the table will lock into place at often used miter angles, including 22.5º, 30º, 45º, and 90º on both left and right sides.

4.Tighten the Miter Knob after adjusting the miter angle.

5.With the Table adjusted to the desired angle, place the workpiece flush against the Fence, secure it with the Clamp and make the cut.

Setup

Adjusting the Bevel Angle

A bevel cut is one that is at an angle vertically. Bevel cuts can be used to cut a miter in relatively wide and thin material. Bevel cuts can be used in combination with a miter cut to form a compound angle. Compound angle cuts are often used in crown moldings, picture frames and similar trim materials.

1.

Loosen the Bevel Lock Lever at the rear of the saw.

 

2.

Move the blade assembly to the desired angle.

 

 

Read the angle on the Bevel Angle Indicator.

 

3.

Lock the blade assembly into position by

Bevel Angle

 

rotating the Bevel Lock Lever clockwise.

 

Indicator

 

Tighten firmly but do not over-tighten.

 

 

4.

Make a sample cut in a piece of scrap to

Bevel Lock

 

confirm that the bevel angle is correct.

Lever

If it is not, correct the angle before cutting.

Figure D

Operation

Maintenance

Item 61971

For technical questions, please call 1-888-866-5797.

Page 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Miter SAW General Tool Safety Warnings Table of Contents25′ 50′ 100′ 150′ Safety Setup Operation MaintenanceVAC Grounded Tools Tools with Three Prong Plugs Miter Saw Safety WarningsSafety Setup OperationMiter Saw Safety Warnings Symbology Vibration SafetyList of Contents Mounting the Saw AssemblySafety Setup Operation MaintenanceBlade Guard operation Description of Selected FunctionsLock Trigger Fence Head Lockdown PinOperating Instructions Replacing the BladeBevel Lock Using the Workpiece Extension SupportsAdjusting the Miter Angle Adjusting the Bevel AngleBatteries for Laser Using the Depth StopAfety Setup Battery BoxGeneral Operating Instructions Workpiece and Work Area Set UpIf Fence needs adjustment Cleaning, Maintenance, and LubricationPeration Maintenance Maintenance and ServicingCalibrating the Bevel Angle Calibrating the Miter Angle IndicatorAdjusting or Replacing the Kerf Board To adjust the Kerf BoardProblem Possible Causes Likely Solutions TroubleshootingPart Description Qty Parts ListSetup Operation Maintenance Parts List and Diagram111 Assembly Diagram Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 Limited 90 Day Warranty

61971 specifications

The Chicago Electric 61971 is a powerful and versatile tool well-regarded in the woodworking community for its efficiency and precision. This electric planer is designed to meet the needs of both amateur and professional woodworkers, making it a popular choice in various workshops.

One of the primary features of the Chicago Electric 61971 is its robust motor, typically offering around 6.5 Amps of power. This ensures that the tool can tackle a wide range of materials, including hardwoods, softwoods, and plywood. The motor drives the planer at a high speed, allowing for efficient material removal and a smooth finish on surfaces.

The adjustable depth control is another notable aspect of this model. Users can easily set the cutting depth according to their specific project requirements, with options usually ranging from 0 to 1/8 inch. This feature not only provides flexibility but also enables precise adjustments, ensuring optimal results.

Portability is also a key characteristic of the Chicago Electric 61971. Weighing in at a manageable level, it is easy to handle and maneuver, making it a suitable choice for both stationary and on-the-go projects. The ergonomic design includes a comfortable grip, reducing fatigue during extended use and enhancing overall control while operating the tool.

Dust collection capability is integral to keeping the workspace clean and free of debris. The Chicago Electric 61971 often features a dust port that can be connected to most standard vacuum systems. This system helps maintain visibility and ensures a healthier working environment by minimizing airborne particles.

Safety features are not overlooked in this model. The inclusion of a safety switch prevents accidental start-ups, which is essential for protecting the user. Additionally, the guard that covers the blades helps reduce the risk of injury, making it safer to operate.

Overall, the Chicago Electric 61971 combines power, precision, and convenience. Whether used for simple edge planing tasks or more involved woodworking projects, this electric planer stands out for its ability to deliver high performance while accommodating the varied needs of its users. With its balance of features, technologies, and thoughtful design, it is an asset to any workshop, enabling craftsmen to achieve professional results with ease.
Top Page Image Contents