Chicago Electric 61971 owner manual Safety Setup Operation Maintenance, 25′ 50′ 100′ 150′

Page 3

General Tool Safety Warnings (continued)

Table A: RECOMMENDED MINIMUM WIRE GAUGE

FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

EXTENSION CORD

AMPERES

 

LENGTH

 

(at full load)

25′

50′

100′

150′

0 – 6

18

16

16

14

6.1 – 10

18

16

14

12

10.1 – 12

16

16

14

12

12.1 – 16

14

12

Do not use.

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table A shows the correct size to use depending on cord length and nameplate ampere rating.

If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended.

Wear protective hair covering to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool.

13.DON’T OVERREACH.

Keep proper footing and balance at all times.

14.MAINTAIN TOOLS WITH CARE.

Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

15.DISCONNECT TOOLS before servicing when changing accessories, such as blades, bits, cutters, and the like.

16.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in

off position before plugging in.

17.USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

18.NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

19.CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that

it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

20.DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

21.NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

Safety

Setup

Operation

Maintenance

Item 61971

For technical questions, please call 1-888-866-5797.

Page 3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Miter SAW General Tool Safety Warnings Table of Contents25′ 50′ 100′ 150′ Safety Setup Operation MaintenanceVAC Grounded Tools Tools with Three Prong Plugs Miter Saw Safety WarningsSafety Setup OperationMiter Saw Safety Warnings Symbology Vibration SafetyList of Contents Mounting the Saw AssemblySafety Setup Operation MaintenanceBlade Guard operation Description of Selected FunctionsLock Trigger Fence Head Lockdown PinOperating Instructions Replacing the BladeBevel Lock Using the Workpiece Extension SupportsAdjusting the Miter Angle Adjusting the Bevel AngleBatteries for Laser Using the Depth StopAfety Setup Battery BoxGeneral Operating Instructions Workpiece and Work Area Set UpIf Fence needs adjustment Cleaning, Maintenance, and LubricationPeration Maintenance Maintenance and ServicingCalibrating the Bevel Angle Calibrating the Miter Angle IndicatorAdjusting or Replacing the Kerf Board To adjust the Kerf BoardProblem Possible Causes Likely Solutions TroubleshootingPart Description Qty Parts ListSetup Operation Maintenance Parts List and Diagram111 Assembly Diagram Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 Limited 90 Day Warranty

61971 specifications

The Chicago Electric 61971 is a powerful and versatile tool well-regarded in the woodworking community for its efficiency and precision. This electric planer is designed to meet the needs of both amateur and professional woodworkers, making it a popular choice in various workshops.

One of the primary features of the Chicago Electric 61971 is its robust motor, typically offering around 6.5 Amps of power. This ensures that the tool can tackle a wide range of materials, including hardwoods, softwoods, and plywood. The motor drives the planer at a high speed, allowing for efficient material removal and a smooth finish on surfaces.

The adjustable depth control is another notable aspect of this model. Users can easily set the cutting depth according to their specific project requirements, with options usually ranging from 0 to 1/8 inch. This feature not only provides flexibility but also enables precise adjustments, ensuring optimal results.

Portability is also a key characteristic of the Chicago Electric 61971. Weighing in at a manageable level, it is easy to handle and maneuver, making it a suitable choice for both stationary and on-the-go projects. The ergonomic design includes a comfortable grip, reducing fatigue during extended use and enhancing overall control while operating the tool.

Dust collection capability is integral to keeping the workspace clean and free of debris. The Chicago Electric 61971 often features a dust port that can be connected to most standard vacuum systems. This system helps maintain visibility and ensures a healthier working environment by minimizing airborne particles.

Safety features are not overlooked in this model. The inclusion of a safety switch prevents accidental start-ups, which is essential for protecting the user. Additionally, the guard that covers the blades helps reduce the risk of injury, making it safer to operate.

Overall, the Chicago Electric 61971 combines power, precision, and convenience. Whether used for simple edge planing tasks or more involved woodworking projects, this electric planer stands out for its ability to deliver high performance while accommodating the varied needs of its users. With its balance of features, technologies, and thoughtful design, it is an asset to any workshop, enabling craftsmen to achieve professional results with ease.
Top Page Image Contents