Craftsman 315.21212 owner manual Operation,clamp, bolt or nail your compound, See

Page 19

&

WARNING: Before starting any cutting

 

operation,clamp, bolt or nail your compound

DEPTHSTOP

miter saw to a workbench. Never operate your

miter saw on the floor or in a crouched position.

ADJUSTMENT

BEVEL

Failure to heed this waming can result in sorious personal injury.

LOCKKNOB

cu'n'ING WITH YOUR COMPOUND

MITER SAW

MITER

PosmvETABLE

STOPADJUSmENTLOCKNUT(S) Fig.25

•Lowerthebladeintothezeroclearancethroat

plataofthe miter table. Check blade clearance and maximum cuttingdistance (distance from fence where blade enters) to front of miter table sloL

•Readjust if necessary.

WARNING: Do not start your compound miter saw without checking for interferencebetween

the blade and the miter table support. Damage could result to the blade if it strikes the miter

table supportduring operation of the saw.

•Tighten the hex nut with a 17 mm wrench or adjustable wrench.

•To prevent the depth stop adjustment screw from tuming while tighteningthe hex nut, carefully held it withthe hex key while tighteningthe hex nut.

APPLICATIONS

(Use only for the purposes limed below)

•Cross cuttingwood and plastic.

•Cross cutting miters,joints, etc. for pictureframes, moldings, door casings, and fine joinery.

Note: The blade provided is fine for most wood cuttingoperations, but for fine joinery cuts or cutting plastic, usa one of the accessory blades available from your nearest Sears store.

&WARNING: When using a work clamp or C-clamp to secure your workpiece, clamp

workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from bindingin workpiece.The workpiece bindingthe blade will cause motor stallingand kickback.This situation could cause an accident resultingin possible serious personal injury.

CROSSCUTTING

See Figure26.

Acrosscutis made by cutting across the grain of the workpiece.A straight crosscutis made with the miter table set at the zero degree position. Miter crosscuts are made with the miter table set st some angle other than zero.

TO CROSSCUT WITH YOUR MITER SAW:

•Pull out the lock pinand lift saw arm to itsfull height.

•Loosen the miter lock handle. Rotate the miter

lock handle approximately one-haftturn to the left to loosen.

•Press the miter lock plate down with your thumb and held.

•Rotate the control arm untilthe pointer aligns with the desired angle on the miter scale.

•Release the miter lock plate.

Note: You can quickly locate 0 °, 15°, 22-1/2°, 31.62°, and 45 ° left or right by releasingthe lock plate as you rotate the controlarm. The lock plate will seat itself in one of the positive stop notches, located in the miter table frame,

•Tighten the miter lock handle securely.

,_ WARNING: To avoid serious personal injury, always tighten the miter lock handle securely before makinga cut. Failure to do so could result in movement of the control arm or miter table

while making a cut.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 12 in. Compound Miter SAW Double Insulated IL Warning Full ONE Year WarrantyDouble Insulation Symbol Meaning Safety Alert SymbolGuard Against Electrical Shock by Rules for Safe Operation Never USE a Length Stop on the Free Before Aking a CUT, be Sure ALL Adjustments are SecureNever Start a Tool When the Blade is AKE Sure the Miter Table and SAWRules for Safe Operation BladeDiameter 12in TRNING/ Adverteni Framingsquare BladewrenchSawblade Miterlockhandle DustguideSee Figure AMP MotorMiter Lock Handle LOCK-OFF Switch TriggerSwitchpadlock Trigger Carrying %% Sawhandle ARM Miterlock Handle SawarmSELF-RETRACTING Lower Blade Guard FenceElectrical Connection Sea Figure To Install BladeSee Figures 10, 11, Spindle Lowerarrow Bladeguard BoltcoverFraming Fence Square Cutting a Slot in the Zero Clearance Throat PlateSquaring the Miter Table To the Fence See Figures 13Miter Blade Table Miter Lockplate Viewofblade Lockhandle Fence FramingHeadscrews Squaring the SAW Blade to the Fence See Figures 17Mitermiter Lockplatelockhandle Squaring the Blade to Miter TableSee Figures Miter Lockplatemiter Lockhandle CorrectviewofbladeTravel Pivot Adjustment See Operation,clamp, bolt or nail your compoundMiter saw to a workbench. Never operate your Miter saw on the floor or in a crouched positionSee Figures27 To Bevel CUT with Your Miter SAWCompound Miter CUT See Figures 33Compound Mitiercut Clamp To Make a Compound CUT with Your Miter SAWLongworkpiece Workpiecesupports M40.89 COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Pitchuber OfsidesCROWNMOI.DIGFLATONMITERTABLE Lfence TopedgeagainstfenceCorner Outside Fencecorner RIGHTSIDE,INSIDECORNER LEFTSIDE,OUTSIDECORNER MitertableWide Board Right Clamping Wide WorkpiecesLubrication GeneralExtension Cords Brush Assemblybrush CAP Brush ReplacementPage Craftsman Compound Miter SAW Model Number Description Quan See Back page for Parts Ordering Instructions3937 KEY Part Parts List for Figure BSeenotea Description Quan Blade Bolt Outer Blade Washer MY-Home s

315.21212 specifications

The Craftsman 315.21212 is a remarkable tool designed to provide efficiency and reliability for a variety of home improvement tasks. This powerful electric tool is primarily known for its precision and versatility, making it a favorite among DIY enthusiasts and professional users alike.

One of the standout features of the Craftsman 315.21212 is its robust motor. With an output of 5.5 amps, this tool delivers sufficient power to handle an array of drilling and cutting applications. Whether you are working on wood, metal, or plastic, its impressive torque offers the strength needed to complete the task with ease, allowing users to efficiently tackle their projects without any downtime.

Another significant characteristic of the Craftsman 315.21212 is its ergonomically designed handle. Built for comfort and grip, the handle minimizes fatigue during prolonged use. This thoughtful design ensures that users can maintain better control and precision, leading to high-quality results, even during extended working hours.

The tool also features a variable speed control mechanism that allows users to adjust the speed according to the specific needs of their project. This flexibility is essential for achieving optimal performance across different materials. Users can quickly switch from higher speeds for quick drilling to lower speeds for more delicate tasks, demonstrating the versatility of the Craftsman 315.21212.

In terms of technology, the Craftsman 315.21212 incorporates a keyless chuck system, making it incredibly convenient to change the drill bits. This feature saves time and enhances productivity, as it eliminates the hassle of using additional tools to swap bits. Plus, the built-in LED light is a practical addition that illuminates the workspace, ensuring precision in dimly lit areas.

The Craftsman 315.21212 also boasts a compact design, making it easy to maneuver in tight spaces. It is lightweight yet durable, ensuring that it can withstand the rigors of frequent use. Overall, this tool combines advanced features with user-friendly aspects, making it a top choice for both casual users and professionals looking for reliable performance in their toolkit. Whether handling home repairs or intricate woodworking projects, the Craftsman 315.21212 is equipped to deliver outstanding results.
Top Page Image Contents