Craftsman 137.21239 operating instructions Accessories and Attachments, Recommended Accessories

Page 12

ACCESSORIES AND ATTACHMENTS

RECOMMENDED ACCESSORIES

!WARNING

●Use only accessories recommended for this miter saw. Follow instructions that accompany accessories. Use of improper accessories may cause hazards.

●The use of any cutting tool except 12 in. saw blades which meet the requirements under recommended accessories

is prohibited. Do not use accessories such as shaper cutters or dado sets. Ferrous metal cutting and the use of abrasive wheels is prohibited.

●Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modiﬁcation is misuse and could result in a hazardous condition leading to possible serious injury.

ACCESSORIES

Visit your Sears Hardware Department or see the Sears Power and Hand Tool Catalog to purchase recommended accessories for this power tool.

!WARNING

To avoid the risk of personal injury, do not modify this power tool or use accessories not recommended by Sears.

!WARNING

Read warnings and conditions on your CARBIDE TIPPED SAW BLADE. Do not operate the saw without the proper saw blade guard in place. Carbide is a very hard but brittle material. Care should be taken while mounting, using, and storing carbide tipped blades to prevent accidental damage. Slight shocks, such as striking the tip while handling, can seriously damage the blade. Foreign objects in the workpiece, such as wire or nails, can also cause tips

to crack or break off. Before using, always visually examine the blade and tips for bent blade, cracks, breakage, missing or loose tips, or other damage. Do not use if damage is suspected. Failure to heed safety instructions and warnings can result in serious bodily injury.

12

Image 12

Contents Sears, Roebuck and Co., Hoffman Estates, lL 60179 USA Table of Contents Warranty Product SpecificationsMotor Blade SizeSymbols ProhibitionSupport and Clamp Work Power Tool Safety USE Proper ExtensionAlways Wear EYE Wear a Face Mask or DustDisconnect Tools from Reduce the Risk24. ! Danger People Compound Miter SAW Safety Power Supply and Motor Specifications Electrical RequirementsMotor Safety Protection Important Electrical Requirements cont’dDouble Insulated Guidelines for Extension Cords Be sure your extension cord isUse a separate electrical circuit Accessories and Attachments Recommended AccessoriesAccessories Tools Needed for Assembly Supplied Not supplied Blade WrenchHex Key Combination Square Must be TrueCarton Contents Know Your Sliding Miter SAW Glossary of Terms Instruction or OWNER’SWoodworking Terms Revolutions PER Minute RPMAssembly and Adjustments Estimated Assembly Time 5 10 minutesInstalling the Miter Handle FIG. a Unlocking the Slide Carriage FIG. BInstalling the Exhaust Port and the Dust BAG FIG. E Installing the HOLD-DOWN Clamp FIG. F and GRemoving and Installing the Table Insert FIG. H LockingFig. H Mounting the Miter SAW FIG. I, JRemoving or Installing the Blade For portable use, placeInstalling Blade FIG. K, L, M Fig. MLaser Beam Class II Laser ProductBevel Pointer Adjustment Fig. O Bevel Adjustment Fig. PMiter Angle Adjustment FIG. Q Miter Scale Indicator Adjustment FIG. QAdjusting Fence Squareness FIG. R Setting Cutting Depth FIG. SAdjusting Cutting Depth FIG. S Sliding the Rear Extension Support BAR FIG. T Fig. TAdjustments Requirements and Safety Before Each USE Inspect Your SAWOperation Keep Your Work Area Clean Plan Your WorkDress for Safety Inspect Your WorkpieceDo not OVER-REACH Never cut freehandWhen SAW is Running Body and Hand Position FIG. U Finishing a cutBefore freeing jammed material Basic SAW OperationsSliding Fence & Remove Sliding Fence FIG. W Sliding FenceSliding Carriage System FIG Before Leaving the SAW Miter CUT FIG. YBevel CUT FIG. Z Bevel Stop for Crown Molding FIG. AA Compound CUT FIG. BBTo Slide Cut Wide Boards Fig. CC Fig. DD Fig. CCAuxiliary Wood Fence FIG. FF Cutting Base Molding FIG. GGBevel/Miter Settings Only When the Angle Between the Walls EqualsCutting Crown Molding FIG. HH Equal exactlyCrown Molding Chart Compound Miter sawMaintenance MaintenanceReplacing Carbon Brushes FIG. JJ Lower Blade GuardSawdust Lubrication FIG. KKCentral pivot of plastic guard Use Troubleshooting Guide EYE Protection Parts List Schematic a Parts List for SAW Schematic B Schematic B Parts List for Motor Page Get it fixed, at your home or ours