Craftsman 137.21239 Sawdust, Lubrication FIG. KK, Central pivot of plastic guard Use

Page 41

MAINTENANCE

SAWDUST

Periodically, sawdust will accumulate under the worktable and base. This could cause difﬁculty in the movement of the worktable when setting up

a miter cut. Frequently blow out or vacuum up the sawdust.

!WARNING

If blowing sawdust, wear proper eye protection to keep debris from blowing into eyes.

LUBRICATION (FIG. KK)

All the motor bearings in this tool are lubricated with a sufﬁcient amount of high-grade lubricant for the life of the unit under normal operating conditions; therefore, no further lubrication is required.

Lubricate the following as necessary:

Chop pivot: Apply light machine oil to points indicated in illustration.

Central pivot of plastic guard: Use

light household oil (sewing machine oil) on metal-to-metal or metal-to- plastic guard contact areas as required for smooth, quiet operation. Avoid excessive oil, to which sawdust will cling.

Link: (which actuates the lower guard movement) may be oiled at the rear pivot, greased at ball bearing contact, and oiled where the link actuates the acetyl roller of the lower guard, if the down chop motion is hard to start.

Fig. KK

Link

Link

Chop pivot

Central pivot of plastic guard

41

Image 41

Contents Sears, Roebuck and Co., Hoffman Estates, lL 60179 USA Table of Contents Product Specifications WarrantyMotor Blade SizeSupport and Clamp Work SymbolsProhibition USE Proper Extension Power Tool SafetyWear a Face Mask or Dust Always Wear EYEDisconnect Tools from Reduce the Risk24. ! Danger People Compound Miter SAW Safety Electrical Requirements Power Supply and Motor SpecificationsDouble Insulated Motor Safety Protection ImportantElectrical Requirements cont’d Use a separate electrical circuit Guidelines for Extension CordsBe sure your extension cord is Accessories Accessories and AttachmentsRecommended Accessories Supplied Not supplied Blade Wrench Tools Needed for AssemblyHex Key Combination Square Must be TrueCarton Contents Know Your Sliding Miter SAW Instruction or OWNER’S Glossary of TermsRevolutions PER Minute RPM Woodworking TermsEstimated Assembly Time 5 10 minutes Assembly and AdjustmentsInstalling the Miter Handle FIG. a Unlocking the Slide Carriage FIG. BInstalling the HOLD-DOWN Clamp FIG. F and G Installing the Exhaust Port and the Dust BAG FIG. ERemoving and Installing the Table Insert FIG. H LockingMounting the Miter SAW FIG. I, J Fig. HFor portable use, place Removing or Installing the BladeFig. M Installing Blade FIG. K, L, MClass II Laser Product Laser BeamBevel Adjustment Fig. P Bevel Pointer Adjustment Fig. OMiter Scale Indicator Adjustment FIG. Q Miter Angle Adjustment FIG. QAdjusting Cutting Depth FIG. S Adjusting Fence Squareness FIG. RSetting Cutting Depth FIG. S Fig. T Sliding the Rear Extension Support BAR FIG. TOperation AdjustmentsRequirements and Safety Before Each USE Inspect Your SAW Plan Your Work Keep Your Work Area CleanInspect Your Workpiece Dress for SafetyDo not OVER-REACH Never cut freehandWhen SAW is Running Finishing a cut Body and Hand Position FIG. UBefore freeing jammed material Basic SAW OperationsSliding Carriage System FIG Sliding Fence & Remove Sliding Fence FIG. WSliding Fence Bevel CUT FIG. Z Before Leaving the SAWMiter CUT FIG. Y To Slide Cut Wide Boards Fig. CC Bevel Stop for Crown Molding FIG. AACompound CUT FIG. BB Fig. CC Fig. DDCutting Base Molding FIG. GG Auxiliary Wood Fence FIG. FFOnly When the Angle Between the Walls Equals Bevel/Miter SettingsCutting Crown Molding FIG. HH Equal exactlyCompound Miter saw Crown Molding ChartMaintenance MaintenanceReplacing Carbon Brushes FIG. JJ Lower Blade GuardCentral pivot of plastic guard Use SawdustLubrication FIG. KK Troubleshooting Guide EYE Protection Parts List Schematic a Parts List for SAW Schematic B Schematic B Parts List for Motor Page Get it fixed, at your home or ours