Craftsman 113.244513 BREAKAGE. Follow Adjusting Blade, Creates a drag between the wheel guide

Page 10

assembly

9. Loosen the two screws that secure the lower blade guides and separate them about 1/8".

10.Loosen the screw holding the lower blade guide support and slide support all the way toward the rear of the saw, and retighten all screws.

WARNING: TO AVOID BEING SCRAPED

SHOULD BLADE SUDDENLY UNCOIL, WEAR

SAFETY GOGGLES AND CAREFULLY UNCOIL THE BLADE HOLDING IT AT ARMS LENGTH.

11.Place the blade over the wheels with the teeth pointing downward toward the table as shown. Make sure the blade is in the center of the rubber tires.

NOTE: Your bandsaw can use 1/8 or 114 inch wide blades, 56-718inches long. A l14inch blade is included with this saw.

TENSIONING THE BLADE

The bandsaw is equipped with a self-limiting tension device. The tension is factory set and

should not need adjustment. The blade must be installed before tension can be set.

1. Turn tension adjustment knob until knob

contacts washer and sleeve.

2. DO NOT turn knob after contact is made and resistance if felt. This is the proper tension

setting tor a114" blade.

3. To release tension turn knob counterclock- wise until knob is above the washer and

sleeve.

COMPENSATION FOR WEAR

Tension screw is provided to make minimal adjustments due to wear. The tension screw

creates a drag between the wheel guide and the

frame.

1. Remove the blade before adiusting.

2. Use a phillips screw driver to adjust the ten' sion screw. Turn clockwise to increase the

drag (tension).

3. Check tension by lifting up on tension knob. lf the tension knob will not move the tension screw is too tight. Adjust by turntng tension screw coun-

terclockwise and recheck,

ry

:.

IENSION WHEEL

SIOT IN TABLE

DRIVE V/IEEt

DLER WHEET

TENSION SCREW

WARNING: OVER TENSION AND FAILURE TO PROPERLY SET BLADE GUIDES AND THRUST BEARING WILL CAUSE PREMATURE BLADE

BREAKAGE. FOLLOW ADJUSTING BLADE

GUIDE ASSEMBLIES COMPLETELY TO HELP Q MAINTAIN NORMAL BLADE LIFE.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Caref ully Read GeneralFor future use General safety instructions for power tools Tain long hair. Roll long sleeves aboveWhen Installing or Moving Additional safety instructions for band sawBefore Using the SAW Before Each USEWhenever SAW is Running Cord and grounding type plug which has a RequirementsQir-t Grounding prong, approved by UnderwritersContents Unpacking Checking contentsAssembly TNOTE For proper stability, holes must beWith thd trunnion against mounting rib Securely clamp board to workbench usingPlace table assembly onto band saw frame ClampsInstalled, assembly continues on p ,Tension Locate bevel indicator and 10-24x114 panInstall bevel indicator and screw as shown Loosen the two screws in the frontContacts washer and sleeve BREAKAGE. Follow Adjusting BladeCreates a drag between the wheel guide Remove the blade before adiustingClockwise a few turns and notice if Tilt table ---.-rt.r alinn tableBlade guides and press the two guides evenly Loosen the two screws that lock the lowerTime Turns to check blade travel and clearanceDental START, Unplug Tool Before Band sawTable f lat ano rn alignment Getting to know Your band saw Guide assembly and lock the guide bar byLoose parts bag Insert f inger under switch lever and Puil Guide bar lock knob . . . The upper bladeRight Planning ahead by turning workpiece Naticrn line as secttonS are cut off of curveWood cutting band Saw blades are lTires onto wheels aligning tires inside wheel Maintenance924214 Troubleshooting Repair parts Tcq f?iI $Fe 5+ IFF,*gsEi#ein+ci?EEi+ii at = =Be found on a plate at the right-hand side VisitModel number of your 1O-lnch Band Saw will Lnch Band Saw

113.244513 specifications

The Craftsman 113.244513 is a versatile and powerful table saw designed to cater to both amateur woodworkers and seasoned professionals. With its impressive combination of features, technologies, and practical characteristics, it stands out in the market for home woodworking projects.

At the heart of the Craftsman 113.244513 is a robust 1.5 HP motor that ensures smooth and efficient operation. This powerful motor allows the saw to handle various materials, from soft pine to harder hardwoods, with ease. Its ability to sustain high-speed performance even during tough cuts not only enhances productivity but also provides users with confidence in achieving precise results.

One of the key features of this table saw is its precision-engineered cast iron table surface. This provides an exceptionally flat and stable platform for cutting, which is critical for achieving accurate measurements. The table’s ample working area allows for larger workpieces, making it ideal for cabinet making, furniture construction, and other demanding tasks.

The Craftsman 113.244513 includes a reliable and adjustable fence system. This easy-to-use fence ensures that users can make straight cuts consistently, thanks to its locking mechanism that reduces the chance of any movement during operation. Additionally, the saw features a miter gauge for angled cuts, allowing for greater versatility in woodworking projects.

Safety is paramount with the Craftsman 113.244513, as it is designed with various safety features to protect users while operating the saw. A blade guard covers the saw blade during use, while a push stick is included to help users safely maneuver smaller pieces of wood without risking injury. The saw also features a power switch that is conveniently placed for quick access, facilitating immediate shut-off when needed.

Another noteworthy characteristic of the Craftsman 113.244513 is its portability. While it is a robust table saw, it is equipped with wheels and a foldable stand, making it easy to move and store when not in use. This feature is particularly beneficial for woodworkers who may work in different locations or have limited storage space.

In summary, the Craftsman 113.244513 table saw is a well-rounded tool that offers outstanding performance, precision, and safety features. With its powerful motor, durable construction, easy-to-use adjustments, and focus on safety, it is an excellent choice for anyone looking to enhance their woodworking capabilities. Whether for hobbyist or professional use, this table saw promises reliable results in various woodworking applications.
Top Page Image Contents