Craftsman 113.244513 owner manual Requirements, Qir-t, Cord and grounding type plug which has a

Page 5

motor specifications and electrical

requirements

This machine is designed to use, and is equipped with, a1725 RPM motor. lt is wired for operation on 120 volts, 60 Hz., alternating current. (TOOL MUST NOT BE CON- VERTED TO OPERATE ON 230 VOLT).

For replacement motor refer to oarts list in this manual.

CONNECTING TO POWER SUPPLY OUTLET This machine must be grounded while in use to protect the operator from electric shock.

Plug power cord into a 120V properly grounded type outlet protected by a 15-amp fuse or circuit breaker.

lf you are not sure that your outlet is properly grounded, have it checked by a qualif ied electri- cian.

WARNING: DO NOT PERMIT FINGERS TO TOUCH THE TERMINALS OF PLUGS WHEN INSTALLING OR REMOVING THE PLUG TO OR FROM THE OUTLET.

WARNING: IF NOT PROPERLY GROUNDED THIS POWER TOOL CAN CAUSE AN ELECTRI. CAL SHOCK PARTICULARLY WHEN USED IN DAMP LOCATIONS CLOSE TO PLUMBING. IF AN ELECTRICAL SHOCK OCCURS THERE IS THE POTENTIAL OF A SECONDARY HAZARD SUCH AS YOUR HANDS CONTACTING THE SAW BLADE.

lf power cord is worn or cut, or damaged in any way, have it replaced immediately.

Your unit is for use on 120 volts, and has a plug that looks like below

qi'r"-<t

PRONG

PROPERLY

GRO U N DED 3.PRONG OUTLET

 

This power tool is equipped with a 3-conductor

 

cord and grounding type plug which has a

 

grounding prong, approved by Underwriters'

 

Laboratories and the Canadian Standards Associ-

\Y

atlon. The ground conductor has a green jacket

and is attached to the tool housing at one end

 

and to the ground prong in the attachment plug

 

at the other end.

This plug requires a mating 3-conductorground- ed type outlet as shown.

lf the outlet you are planning to use for this power tool is of the two prong type, DO NOT

REMOVE OR ALTER THE GROUNDING PRONG

lN ANY MANNER. Use an adapter as shown

below and always connect the grounding lug to a known ground.

It is recommended that you have a qualif ied elec- trician replace the TWO prong outlet with a pro- perly grounded THREE prong outlet.

GROUNDING LUG

SCREW

\

3-PRONG \

MAKE SURE THIS IS

PLUG

CONNECTED TO A

 

KNOWN GROUND

 

2-PRONG

 

RECEPTACLE

 

ADAPTER

An adapter as illustrated is available for connect- ing plugs to 2-prong receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as to a properly grounded outlet box.

NOTE: The adapter illustrated is for use only if you already have a properly grounded 2-prongreceptacle. Adapter is not allowed in Canada by the Canadian Electrical Code.

The use of any extension cord will cause some loss of power. To keep this to a minimum and to

prevent overheating and motor burn-out, use the table below to determine the minimum wire size (A.W.G.) extension cord.

Use only 3 wire extension cords which have 3- prong grounding type plugs and 3-prong recep- tacles which accept the tools plug.

Lenglh of the

Wire Sizes Required

Conductor

(American Wire Gage Number)

 

120V Lines

0 - 25 Feet

No. 16

26 - 50 Feet

No.'14

51 - 100 Feet

No. 12

Page 4 Page 6
Image 5
Page 4 Page 6
Contents For future use Read GeneralCaref ully Tain long hair. Roll long sleeves above General safety instructions for power toolsBefore Using the SAW Additional safety instructions for band sawWhen Installing or Moving Before Each USEWhenever SAW is Running Qir-t RequirementsCord and grounding type plug which has a Grounding prong, approved by UnderwritersUnpacking Checking contents ContentsTNOTE For proper stability, holes must be AssemblyPlace table assembly onto band saw frame Securely clamp board to workbench usingWith thd trunnion against mounting rib ClampsInstall bevel indicator and screw as shown Locate bevel indicator and 10-24x114 panInstalled, assembly continues on p ,Tension Loosen the two screws in the frontCreates a drag between the wheel guide BREAKAGE. Follow Adjusting BladeContacts washer and sleeve Remove the blade before adiustingTilt table ---.-rt.r alinn table Clockwise a few turns and notice ifTime Loosen the two screws that lock the lowerBlade guides and press the two guides evenly Turns to check blade travel and clearanceTable f lat ano rn alignment Band sawDental START, Unplug Tool Before Loose parts bag Insert f inger under switch lever and Puil Guide assembly and lock the guide bar byGetting to know Your band saw Guide bar lock knob . . . The upper bladeWood cutting band Naticrn line as secttonS are cut off of curveRight Planning ahead by turning workpiece Saw blades are l924214 MaintenanceTires onto wheels aligning tires inside wheel Troubleshooting Tcq f Repair parts?EEi+ii at IFF,*gsEi#ein+ci?iI $Fe 5+ = =Model number of your 1O-lnch Band Saw will VisitBe found on a plate at the right-hand side Lnch Band Saw

113.244513 specifications

The Craftsman 113.244513 is a versatile and powerful table saw designed to cater to both amateur woodworkers and seasoned professionals. With its impressive combination of features, technologies, and practical characteristics, it stands out in the market for home woodworking projects.

At the heart of the Craftsman 113.244513 is a robust 1.5 HP motor that ensures smooth and efficient operation. This powerful motor allows the saw to handle various materials, from soft pine to harder hardwoods, with ease. Its ability to sustain high-speed performance even during tough cuts not only enhances productivity but also provides users with confidence in achieving precise results.

One of the key features of this table saw is its precision-engineered cast iron table surface. This provides an exceptionally flat and stable platform for cutting, which is critical for achieving accurate measurements. The table’s ample working area allows for larger workpieces, making it ideal for cabinet making, furniture construction, and other demanding tasks.

The Craftsman 113.244513 includes a reliable and adjustable fence system. This easy-to-use fence ensures that users can make straight cuts consistently, thanks to its locking mechanism that reduces the chance of any movement during operation. Additionally, the saw features a miter gauge for angled cuts, allowing for greater versatility in woodworking projects.

Safety is paramount with the Craftsman 113.244513, as it is designed with various safety features to protect users while operating the saw. A blade guard covers the saw blade during use, while a push stick is included to help users safely maneuver smaller pieces of wood without risking injury. The saw also features a power switch that is conveniently placed for quick access, facilitating immediate shut-off when needed.

Another noteworthy characteristic of the Craftsman 113.244513 is its portability. While it is a robust table saw, it is equipped with wheels and a foldable stand, making it easy to move and store when not in use. This feature is particularly beneficial for woodworkers who may work in different locations or have limited storage space.

In summary, the Craftsman 113.244513 table saw is a well-rounded tool that offers outstanding performance, precision, and safety features. With its powerful motor, durable construction, easy-to-use adjustments, and focus on safety, it is an excellent choice for anyone looking to enhance their woodworking capabilities. Whether for hobbyist or professional use, this table saw promises reliable results in various woodworking applications.
Top Page Image Contents