Graco 309550Y important safety instructions Personal Protective Equipment

Page 7

Warning

WARNING

PERSONAL PROTECTIVE EQUIPMENT

You must wear proper protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:

•Protective eyewear

•Clothing and respirator as recommended by the fluid and solvent manufacturer

•Gloves

•Hearing protection.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

•Read Material Safety Data Sheet (MSDS) to know the specific hazards of the fluids you are using.

•Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

SKIN INJECTION HAZARD

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

•Do not point the gun at anyone or at any part of the body.

•Do not put your hand or fingers over the gun fluid nozzle.

•Do not stop or deflect leaks with your hand, body, glove, or rag.

•Do not “blow back” fluid; this is not an air spray system.

•Follow Pressure Relief Procedure, page 15, when you stop spraying and before cleaning, check- ing, or servicing equipment.

•Use lowest possible pressure when flushing, priming, or troubleshooting.

•Engage piston safety lock when not spraying.

•Tighten all fluid connections before operating the equipment.

•Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. High pres- sure hose cannot be recoupled; replace the entire hose.

BURN HAZARD

Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe burns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely.

309550Y

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Plural Component, Impingement Mix Air Purge Spray Gun Manual Conventions ContentsRound Pattern Guns List of Models/Mix Chamber Selection GuideFlat Pattern Guns 249526 Flat Pattern Stud Wall GunNo., Series In. mm In. mm 1000 psi MPa, 70 bar 249525Non 11 Ratio Guns Spatter Pattern GunWide Round Pattern Gun Four-Hose GunPersonal Protective Equipment Fire and Explosion Hazard Key Overall ViewGrounding Piston Safety LockIsocyanate Hazard Keep a and B Components SeparateTurning Air Cap Follow Pressure Relief Procedure,Loss of Air Pressure Resin ISO SetupSetup Shutdown Pressure Relief Procedure Remove Front End, Optional ConfigurationsOptional Fluid Manifold PositionOptional Hose Position Follow Pressure Relief Procedure, page 15. AlsoFlat Spray Tips Maintenance Clean Fluid Manifold Clean Outside of GunClean Air Cap Clean MufflerNozzle Drill Bit Sizes Clean Mix Chamber NozzleClean Passages Clean Impingement PortsCbip Impingement Port Drill Bit SizesProblem Cause Solution TroubleshootingProblem Cause Solution Gun Triggered Fluid Spraying Theory of OperationGun Detriggered Air Purging Cutaway View Remove Front End RepairTools Required LubricationX Z Attach Front EndMix Chamber and Side Seal Cartridges 18 B Check Valves Piston Air Valve Piston Safety LockCheck Valve 26 Detail PartsSee Supplied Tools, Part No. Description QtyRound Pattern Guns, See Flat Pattern Guns,Detail Views Mix Chamber Part No. Reference Guide Mix Chamber KitsRound Pattern Guns Flat Pattern GunsFlat Tip Part No. Reference Guide Flat Tip KitsGun Repair Kits Check Valve Filter Screen KitsKit Part No Qty in Kit Drill Bit Size Illustration Nominal Drill Bit Kits248969 Air Purge Handle Cleanout Drill KitDrill Bit Kit 119386Polycarballoy Side Seal Kits AccessoriesWide Pattern Mix Chamber Kits Stainless Steel Side Seal KitsFlat Pattern Stud Wall Kit Extension Tip KitsExtension Tip Seal Kits Extension Tip Air Cap KitGun Cover Spatter Conversion KitSolvent Flush Canister Kit Pour Nozzle KitGun Cleaning Kit Tip Cleanout ToolCirculation Manifold Air Flow Data in scfm m3/min Technical DataCategory Data Graco Information Graco Standard WarrantyToll Free
Top Page Image Contents