Campbell Hausfeld HV2100, HV2105 Grounding Instructions, Length of Cord Gauge

Page 3

Operating Instructions and Parts Manual

HV2100, HV2105

HVLP Paint Sprayers

General Safety Information (Cont.)

SPECIAL NOTE ON LACQUERS AND OTHER OIL (SOLVENT) BASED COATINGS

When mixing or thinning:

1.Eliminate potential sources of fire

•Turn off the HVLP sprayer, all other electrical appliances, spark or flame sources

•Follow lacquer (or other coating) and thinner (solvent) manufacturer directions very carefully

2.Minimize vapors in the spray area. Eliminate all potential for spilling lacquer or thinner in the spray area

•Tightly recap all containers immediately after mixing or thinning and store away from the spray areas.

•Do not operate the HVLP turbine in the presence of open containers or spillage.

•Make sure all vapors have dispersed prior to turning the HVLP sprayer on.

!WARNING

•Hazardous vapors: Paints,

solvents, insecticides, and other materials may be harmful if inhaled, causing severe nausea, fainting, or poisoning.

•Always wear a mask or respirator and eye protection

when painting. Be certain mask or respirator will provide necessary protection against inhalation of harmful vapors.

•When not in use, be sure to disconnect the hose and place the gun on a solid, level surface or in the turbine gun storage area to avoid tipping.

GROUNDING INSTRUCTIONS

This product must be properly grounded. In the event of an electrical short circuit, grounding reduces the risk of electrical shock by providing an alternate path for the electrical current.

This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet that is properly installed and grounded in accordance with local codes and ordinances.

 

Grounded

 

Outlet

TEST

RESET

Grounding Pin

Grounded Outlet

Figure 1 - Grounding

Box

 

! DANGER

Improper installation of the ground plug can result in the risk of electrical shock. If

repair or replacement of the plug or cord is necessary, consult an authorized service provider.

1.For any questions regarding proper installation of the ground plug, consult a qualified (licensed or certified) electrician.

2.Do not modify the plug provided. If the plug does not fit the outlet, have the proper outlet installed by a qualified electrician.

3.This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug in Figure 1. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapters should be used with this product.

4.If an extension cord is required, use only a three wire extension cord that has the same configuration as the unit cord, including the (round) ground terminal. Make sure that the extension cord is plugged into a properly grounded receptacle.

5.When using an extension cord, be sure it is in good condition and heavy enough to meet the specifications in the chart below. If an extension cord is needed, the following wire sizes must be used (See Table 1).

•NEVER point the spray gun at any part of the body, or at anyone else.

!CAUTION

•Tipping the gun may cause the gun to clog. Dried spray material clogs the pressure delivery tube and fittings. The spray gun does not function when clogging occurs.

Extension Cord Requirements

Length of Cord

Gauge

 

 

25’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 25-50’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 50-100’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 100-150’ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Table 1 - Appropriate Extension Cord Lengths

www.chpower.com

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Operating Instructions and Parts Manual HV2100, HV2105Description Table of ContentsSafety Guidelines General Safety InformationLength of Cord Gauge Grounding InstructionsPreparing to USE Your Hvlp Turbine System How Your Hvlp System WorksHow Your Hvlp Spray Gun Works Pre-OperationTip/Needle Size Application Air Cap CoatingsSpray Patterns Using Your Spray GUNOperation Preparing to SprayRunning Multiple Spray Guns with a Turbine Spraying TechniqueAdditional Instructions for Model HV2105 Attaching AIR Hose and Fluid Hose Setting POT Pressure and Priming Spray GUNCleaning Your Spray GUN MaintenanceCleaning the System Turbine MaintenanceHvlp Paint Sprayers Symptom Possible Causes Corrective Action Troubleshooting ChartParts Not Pictured Turbine Repair PartsSpray Gun with Quick Release Cup Ref. No Description Part Number Qty Parts List for Spray Gun with Quick Release CupCart Assembly For Model HV2105 only Parts List for Cart Assembly, For Model No. HV2105 Only Fluid Tank Assembly For Model HV2105 only HV2100, HV2105 Limited Warranty

HV2100, HV2105 specifications

The Campbell Hausfeld HV2105 and HV2100 models represent a significant advancement in airless paint sprayer technology. These units are engineered for homeowners and DIY enthusiasts seeking efficient, high-quality painting solutions. Both models deliver a user-friendly experience while ensuring professional results, making them ideal for various painting projects around the home.

The HV2105 and HV2100 feature a powerful motor that enables consistent paint flow, ensuring uniform coverage on surfaces. The HV2105 is specially designed for small to medium-sized projects, such as fences, furniture, or accent walls, while the HV2100 is suitable for larger applications, including exterior walls and large indoor spaces. The adjustable pressure settings allow users to customize the paint flow, catering to different project requirements and types of coatings.

One of the standout features of these models is their advanced technology, which eliminates the need for thinning paint. This not only saves time but also ensures that users can achieve a smooth finish without the hassle of preparing the paint. Additionally, the airless design provides fast operation, allowing users to complete their projects more quickly than traditional painting methods.

Another key characteristic of the HV2105 and HV2100 is their lightweight and portable construction. These sprayers weigh significantly less than many conventional models, making them easy to maneuver and transport from one location to another. This is particularly beneficial for projects that require mobility or for users who may need to work on scaffolding or ladders.

The ergonomic design of the spray gun enhances comfort during use, reducing fatigue and strain on the user’s hands and arms. Furthermore, both models come equipped with an easy-clean system that simplifies maintenance after use, ensuring longevity and optimal performance over time.

In summary, the Campbell Hausfeld HV2105 and HV2100 airless paint sprayers are excellent choices for anyone looking to achieve a professional finish with ease. Their powerful motor, adjustable settings, lightweight design, and user-friendly features combine to make painting projects more efficient and enjoyable. Whether tackling small touch-ups or larger painting jobs, these sprayers stand out in the competitive market, delivering reliability and quality that users can trust.
Top Page Image Contents