Harbor Freight Tools 44505 operating instructions 25’ 50’ 100’ 150’, Table a

Page 4

8.USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

EXTENSION CORD

AMPERES

 

LENGTH

 

(at full load)

25’

50’

100’

150’

0 – 6

18

16

16

14

6.1 – 10

18

16

14

12

10.1 – 12

16

16

14

12

12.1 – 16

14

12

Do not use.

TABLE A

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table A shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool.

13.DON’T OVERREACH. Keep proper footing and balance at all times.

14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

15.DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like.

16.REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in.

17.USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

18.NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

19.CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

20.DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

21.NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

Page 4

For technical questions, please call 1-800-444-3353.

SKU 44505

Image 4
Contents For technical questions or replacement parts, please call Drill PressContents Save This Manual General Tool Safety WarningsSave all warnings and instructions for future reference 25’ 50’ 100’ 150’ Table aDrill Press Safety Warnings Grounding Instructions110-120 V~ Grounded Tools Tools With Three Prong Plugs 125 V~ 3-Prong Plug and OutletDo not operate with ANY guard disabled, damaged, or removed Vibration SafetyFor technical questions, please call Specifications Assembly/MountingUnpacking Instructions for putting Into useOperating Instructions Tool Set Up Work Piece and Work Area Set UpGeneral Operating Instructions Tilting the TableSKU For technical questions, please call Maintenance Servicing Cleaning, Maintenance, LubricationInstalling the Chuck and Spindle Shaft Removing the Chuck and Spindle ShaftAdjusting the Feed Wheel Return Tension Spring Troubleshooting Problem Possible Causes Likely SolutionsParts Lists and Diagrams Head Assembly Parts ListPart Description Record Product’s Serial Number HereHead Assembly Diagram Parts List and Diagram a Pulley and Spindle Parts List and Diagram B Chuck and Spindle Shaft Parts List and Diagram C Base and Table Limited 90 DAY Warranty