![](/images/new-backgrounds/1283534/28353411x1.webp)
English
SPECIFICATIONS
Voltage (by areas)* | (110V, 115V, 120V, 127V, 220V, 230V, 240V) |
Power input | 950 W* |
Capacity | Drill bit: 40 mm |
| Core bit: 105 mm |
No load speed | 360/min. |
2800/min. | |
Weight (without cord, side handle) | 6.5 kg |
•Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES |
| |
(1) | Case (Molded plastic) | 1 |
(2) | Side Handle | 1 |
(3) | Stopper | 1 |
(4) | Hexagon Bar Wrench (for 6 mm screw) | 1 |
(5) | Hexagon Bar Wrench (for 5 mm screw) | 1 |
(6) | Hammer Grease A | 1 |
(7) | Dust cup | 1 |
Standard accessories are subject to change without | ||
notice. |
|
OPTIONAL ACCESSORIES (sold separately)
◯
(1) Drill bit (hexagon shank)
Overall length: 280, 400, 505 mm
External dia.: 16, 19, 22, 25, 28, 32, 38 mm
◯Anchor hole drilling (Rotation + Striking)
(3)Cotter
(1) Drill bit (taper shank) | (2) Taper shank | ||
External dia.: 11, 12, 14. | adapter | ||
| 3, 14.5, 17. |
| |
| 5, 21.5 mm |
| |
|
|
|
|
Taper shank |
| Application drill bit | |
adapter |
| ||
|
|
| |
Morse taper |
| Drill bit (taper shank) | |
(No. 1) |
| 11, 12, 14.3, 14.5, 17.5 mm | |
Morse taper |
| Drill bit (tape shank) | |
(No. 2) |
| 21.5 mm |
|
|
|
| |
| Taper shank adapter formed A- | ||
| taper or | ||
|
| ||
| optional accessory, but drill bit for | ||
| it is not provided. | ||
|
| ||
|
|
|
|
◯Large dia. hole boring (Rotation + Striking)
(1) Center | (Guide | (2) Core | (3) Core bit |
pin | plate) | bit | shank |
(1) Center pin
⬤Applied to core bits from 38 mm to 105 mm
⬤Applied to core bits 32 mm and 35 mm
NOTE
Do not use core bits 25 mm or 29 mm.
(2) Core bit
⬤External dia. 25, 29, 32, 35, 38, 45, 54, 64, 79, 94, 105 mm
(with guide plate, not applicable to cores 25 mm
or 29 mm)
(3) Core bit shank
⬤Applied to core bits above 38 mm
⬤Applied to core bits below 35 mm ◯ Anchor work (for
(1)Anchor adapter (for Rotation + Striking) Anchor sizes:
W1/4, W5/16, W3/8, W1/2, W5/8
(No. 20) (No. 25) (No. 30) (No. 40) (No. 50)
(2)Drift key
◯Crushing (Striking)
(1)Bull point
Overall length: 280, 450 mm
◯Groove digging and edging (striking)
(1)Cold chisel
Overall length: 280, 450 mm
5