DeWalt DC730KAR manual Instructions for use, Using an extension cable, Variable Speed Switch fi g

Page 13

ENGLISH

points in the plug (see below). Brown is for Live

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

(L) (2) and Blue is for Neutral (N) (4).

1.

Align the base of the tool with the notch inside

• Before replacing the top cover of the mains plug

 

the tool’s handle (fig. 2).

ensure that the cable restraint (3) is holding the

2.

Slide the battery pack firmly into the handle until

outer sheath of the cable firmly and that the two

 

you hear the lock snap into place.

leads are correctly fixed at the terminals crews.

 

TO REMOVE THE BATTERY PACK FROM THE TOOL

 

 

1.

Press the battery release buttons (h) and firmly

 

 

pull the battery pack out of the tool handle.

12. Insert battery pack into the charger as

 

 

 

described in the charger section of this manual.

4

 

2

OPERATION

 

 

 

3

 

Instructions for use

 

 

WARNING: Always observe the safety

 

 

 

 

 

 

instructions and applicable regulations.

WARNING: NEVER use a light socket.

NEVER connect the live (L) or neutral (N) wires to the earth

pin marked E or .

Using an extension cable

An extension cord should not be used unless absolutely necessary. Use an approved extension cable suitable for the power input of your charger (see technical data). The minimum conductor size is 1 mm2; the maximum length is 30 m.

Variable Speed Switch (fi g. 1)

To turn the tool on, squeeze the trigger switch (a).

To turn the tool off, release the trigger switch. Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch is fully released.

NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should be avoided.

Forward/Reverse Control Button (fi g. 1)

When using a cable reel, always unwind the cable completely.

A forward/reverse control button (b) determines the direction of the tool and also serves as a lock off button.

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and

adjustment, always remove the battery pack. Always switch off the tool before inserting or removing the battery pack. WARNING: Use only DEWALT battery packs and chargers.

Inserting and removing the battery pack from the tool (fi g. 2)

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury.

To select forward rotation, release the trigger switch and depress the forward/reverse control button on the right side of the tool.

To select reverse, depress the forward/reverse control button on the left side of the tool.

The center position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up. This is normal and does not indicate a problem.

Torque Adjustment Collar (fi g. 1)

Your tool has an adjustable torque screwdriver mechanism for driving and removing a wide array of fastener shapes and sizes and in some models, a hammer mechanism for drilling into masonry. Circling

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page Page Page DC720, DC721, DC722, DC730, DC731, DC732, DC742, DC743 DC720 DC721 DC722 DC725 DC727 DC730 DC731 EnglishEC-Declaration of conformity Definitions Safety GuidelinesWork Area Safety General Power Tool Safety WarningsElectrical Safety Personal SafetyPower Tool USE and Care Drill/Driver/Hammerdrill SafetyService Battery Tool USE and CareImportant Safety Instructions for All Hot/Cold Pack Delay Charging ProcedureImportant Safety Instructions for All Battery Packs ChargersBattery pack fi g Battery Cap fi gLabels on charger and battery pack Storage RecommendationsElectrical safety Package contentsMains plug replacement U.K. & Ireland only Description fi gVariable Speed Switch fi g Using an extension cableInserting and removing the battery pack from the tool fi g Torque Adjustment Collar fi gWorklight fi g Dual Range Gearing fi gKeyless Single Sleeve Chuck fi g Drill Operation fi gOptional accessories CleaningHammerdrill Operation fi g Screwdriver Operation fi gONE Year Free Service Contract Rechargeable Battery PackONE Year Full Warranty Protecting the environmentDC720 DC721 DC722 DC725 DC727 DC730 DC731 14.4 LWA KWA 定义：安全准则 RII   LI-ION   1mm2 EN60335 OFF   Li-Ion NiCd NiMH ͵Ͷͪͤͦ͢͞ͼ ͚ͤ͑ ͚͑͢ ͚ͥ͑ ͚ͣ͑ ͙Λ͚ ͙Ι͚ ͑ ͑͑͑͑͑ ͚͑ͤ͟ ͚͑͟͢ Part NO. N061405

DC730KAR specifications

The DeWalt DC730KAR is a powerful and versatile cordless drill/driver designed for professionals and DIY enthusiasts alike. With its inclusion in the 18V line of tools, the DC730KAR is well known for its performance, durability, and efficiency, making it a reliable choice for a variety of applications.

One of the standout features of the DC730KAR is its compact and lightweight design. Weighing in at just 3.5 pounds, this drill reduces user fatigue during extended use, allowing you to work for longer periods without discomfort. The ergonomic handle provides a secure grip, enhancing control and precision for a variety of tasks.

Power is another significant aspect of the DC730KAR. The drill is equipped with a high-performance motor that delivers a maximum torque of 350 in-lbs, giving users the strength needed for tough applications such as drilling into wood, metal, and plastic. Its dual-speed transmission (0-450 RPM and 0-1500 RPM) allows for flexibility in both drilling and fastening applications, enabling you to match the speed to the specific task at hand.

The DeWalt DC730KAR also features a 1/2-inch single-sleeve ratcheting chuck, which offers a secure grip on a wide range of accessories. This design allows for quick and easy bit changes, optimizing productivity on the job site. Additionally, the drill includes a built-in LED work light, illuminating dark or confined spaces for enhanced visibility and accuracy.

In terms of battery technology, the DC730KAR comes with two 18V NiCad batteries that provide extended operational time. The batteries are compatible with other DeWalt 18V tools, creating flexibility and reducing the need for multiple chargers or spare batteries.

The internal construction of the DC730KAR is designed for durability, featuring high-quality materials that stand up to demanding job site conditions. The tool is built to resist wear and tear, ensuring that it continues to perform reliably over time.

In conclusion, the DeWalt DC730KAR is an exceptional cordless drill/driver that combines power, portability, and precision. With its high-performance motor, dual-speed transmission, ergonomic design, and added features like the LED work light, it is a valuable addition to any toolbox. Whether you are tackling small household projects or larger construction tasks, the DC730KAR delivers the performance needed to get the job done efficiently and effectively.
Top Page Image Contents