Ryobi P220 manual Safety Rules for Charger

Page 5

SAFETY RULES FOR CHARGER

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

nBefore using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the products and possible injury or damage.

CAUTION:

To reduce the risk of electric shock or damage to the charger and battery, charge only nickel-cadmium rechargeable batteries as specifically designated on your charger. Other types of batteries may burst, causing per- sonal injury or damage.

nDo not use charger outdoors or expose to wet or damp conditions. Water entering charger will increase the risk of electric shock.

nUse of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

nDo not abuse cord or charger. Never use the cord to carry the charger. Do not pull the charger cord rather than the plug when disconnecting from receptacle. Damage to the cord or charger could occur and create an electric shock hazard. Replace damaged cords immediately.

nMake sure cord is located so that it will not be stepped on, tripped over, come in contact with sharp edges or moving parts or otherwise subjected to damage or stress. This will reduce the risk of accidental falls, which could cause injury, and damage to the cord, which could result in electric shock.

nKeep cord and charger from heat to prevent damage to housing or internal parts.

nDo not let gasoline, oils, petroleum-based products, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken, or destroy plastic.

n An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)

25’

50’

100’

Cord Size (AWG)

16

16

16

NOTE: AWG = American Wire Gauge

n Do not operate charger with a damaged cord or plug, which could cause shorting and electric shock. If damaged, have the charger replaced by an authorized serviceman.

nDo not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized serviceman for electrical check to determine if the charger is in good working order.

nDo not disassemble charger. Take it to an authorized serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

nUnplug charger from outlet before attempting any maintenance or cleaning to reduce the risk of electric shock.

nDisconnect charger from the power supply when not in use. This will reduce the risk of electric shock or damage to the charger if metal items should fall into the opening. It also will help prevent damage to the charger during a power surge.

nRisk of electric shock. Do not touch uninsulated portion of output connector or uninsulated battery terminal.

nSave these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also to prevent misuse of the product and possible injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

5

Image 5
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsElectrical Safety General Safety RulesPersonal Safety Work AreaService Specific Safety RulesSafety Rules for Charger Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Keyless Chuck Product SpecificationsFeatures Operation AssemblyUnpacking Packing ListCharger Battery Pack Charging the Battery PackCharging a Cool Battery Pack To Install Battery Pack Charging a HOT Battery PackTo Remove Battery Pack Battery Pack LatchesRemoving Bits Inserting BitsDrill BIT Chuck Jaws LockAdjusting the Depth Gauge ROD Adjusting the Auxiliary Handle AssemblyAdjusting the Speed Auxiliary Handle AssemblyForward / Reverse Selector Center Position Lock Adjusting the TorqueChanging the BIT Rotation Maximum Recommended Capacities DrillingHelpful Tips SpeedGeneral Maintenance MaintenanceRemoving the Chuck Chuck JawsBatteries Battery Pack Removal Preparation for RecyclingTightening the Chuck Page Service Model NO. and Serial no