Ryobi HP61 manual Precautions Regarding the USE of Charger and Batteries, Center

Page 5

RULES FOR SAFE OPERATION (Continued)

7.An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

a.That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b.That extension cord is properly wired and in good electrical condition; and

c.That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)

25 ft.

50 ft.

100 ft.

Cord Size (AWG)

16

16

16

Note: AWG = American Wire Gage

8.Do not operate charger with a damaged cord or plug. Replace immediately.

9.Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to an AUTHORIZED SERVICE

CENTER.

10.Do not disassemble charger; take it to an AUTHORIZED SERVICE CENTER when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

11.To reduce risk of electric shock, unplug charger from outletbeforeattemptinganymaintenanceorcleaning. Turning off controls will not reduce this risk.

PRECAUTIONS REGARDING THE USE OF CHARGER AND BATTERIES

1.Do not charge batteries when temperature is below 50° F (10° C) or above 95° F (35° C).

2.The charger is designed to operate on standard household electrical power. Do not attempt to use it on any other voltage.

3.Consecutive charging may cause overheating. If you need to recharge batteries consecutively, wait

for about 15 minutes to allow charger to cool.

4.Do not charge by means of an engine generator or DC power source.

5.Do not store the tool in locations where the temperature may reach or exceed 104° F (40° C), such as outside sheds or metal buildings in summer.

6.Do not incinerate the tool, even if it is severely damaged or completely worn out. The batteries may explode in fire.

7.Battery leakage may occur under conditions of extreme usage or temperature. If liquid comes in contact with skin, wash quickly with soap and water, then with lemon juice or vinegar. If liquid gets in your eyes, wash for at least 10 minutes and seek medical attention immediately.

8.Do not short-circuit the battery.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

SAVE THESE INSTRUCTIONS

Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved.

Page 5

Image 5
Contents Thank YOU for Buying a Ryobi Cordless DRILL-DRIVER Typical Applications Table of ContentsRules for Safe Operation Symbol Meaning Safety Alert SymbolKnow Your Cordless Tool Read ALL InstructionsImportant Safety Instructions for Charger Precautions on Using Your Cordless ToolCenter Precautions Regarding the USE of Charger and BatteriesOperation SpecificationsKnow Your DRILL-DRIVER Charging Your DRILL-DRIVERSwitch Lock SwitchImportant Information for Recharging HOT Batteries ReversibleRight Wrong Installing BitsKeyless Chuck Screwdriving Removing BitsBIT Storage Level DrillingDrilling To Retighten a Loose Chuck Chuck RemovalMallet HEX KEY WrenchBatteries MaintenanceDisposal of Exhausted Batteries Battery RemovalBattery REMOVAL, Preparation for Recycling Owners Operators Manual Cordless DRILL-DRIVER Model NO. HP61
Related manuals
Manual 14 pages 55.43 Kb