Ryobi RTS31 manual Know Your Table SAW, See Figure

Page 10

FEATURES

KNOW YOUR TABLE SAW

See Figure 2.

The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules.

ANTI-KICKBACK PAWLS - Kickback is a hazard in which the workpiece is thrown back toward the operator. The teeth on the anti-kickback pawls point away from the workpiece. If the workpiece should be pulled back toward the operator, the teeth dig into the wood to help prevent or reduce the possibility of kickback.

BEVEL SCALE - The easy-to-read scale on the front of the cabinet shows the exact blade angle.

BLADE - This saw is provided with a 10 in. carbide-tipped blade. The blade is raised and lowered with the height/bevel adjusting handwheel. Bevel angles are locked with the bevel locking lever.

WARNING:

Do not use blades rated less than the speed of this tool. Failure to heed this warning could result in personal injury.

BLADE GUARD - Always keep the blade guard down over the saw blade for through-sawing cuts.

Bevel LOCKING LEVER - This lever, placed just under the saw table surface on the front of the cabinet, locks the angle setting of the blade.

HEIGHT/BEVEL ADJUSTING HANDWHEEL - Located on the front of the cabinet, use this handwheel to lower and raise the blade for height adjustments or blade replacement. This handwheel also makes the adjustment for bevel angles.

LEG STAND - Attached to the table saw base, the leg stand opens and closes with ease making transportation simple.

MITER FENCE WITH LOCK KNOB - The fence attaches to the sliding miter table and can be angled for miter and compound miter cuts as well as straight cuts such as cross cuts and bevel cross cuts. With the locator pin in place, this knob locks the miter fence to the sliding miter table at the desired cutting angle.

RIP FENCE - A sturdy metal fence guides the workpiece and is secured with the locking lever. Grooves run along the top and sides of the rip fence for use with optional clamps and accessories.

RIVING KNIFE - A removable metal piece of the blade guard assembly, slightly thinner than the saw blade, which helps keep the kerf open and prevent kickback. When in the through sawing, or “up” position, it is higher than the saw blade. When in the non-through sawing, or “down” position, it is below the saw blade teeth.

SCALE - Located on the front rail, the easy-to-read scale provides precise measurements for rip cuts.

SLIDING MITER TABLE - The sliding miter table moves allowing the operator to slide the workpiece across the saw table.

SLIDING TABLE EXTENSION - Located on the right side of the saw table, this table extension gives the operator additional support when cutting wide workpieces.

SWITCH ASSEMBLY - This saw has an easy access power switch located below the front rail. To lock the switch in the OFF position, remove the switch key from the switch. Place the key in a location that is inaccessible to children and others not qualified to use the tool.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of contents IntroductionGeneral Safety Rules Read ALL InstructionsPonent is in Contact with the Workpiece Specific Safety Rules Never Start a Tool When ANY ROTATiNG COM  Never Operate the SAW on the FloorSpecific Safety Rules Symbols Symbol Signal MeaningExtension Cords Speed and WiringElectrical Electrical ConnectionGlossary of Terms Features Product SpecificationsKnow Your Table SAW See FigureOperating Components Switch assemblySwitch KEY Switch in Locked Position To Turn Your SAW onFraming Square Phillips Screwdriver Flathead Tools NeededBlades Clamps hex key 3 mmLoose Parts Following items are included with your table sawUnpacking AssemblyTo attach the wheel assembly Mounting HolesTo attach the Leg To install the HandleTo secure/level the saw SET-UP To open/close set-up/tear downLEG Stand To open set-up the leg standTo remove/replace the Throat Plate To Install miter FenceTo move the LEG Stand Throat PlateUnlocked To check SAW Blade installationTo Change riving knife Positions LockedLarge To Install the ANTI-KICKBACK Pawls and Blade GuardSee Figures 15 WrenchVertical Adjustment To Check and Align the riving knife Saw BladeTo store push stick To Store the table saw AccessoriesSee Figures 20 Basic Operation of the Table Saw OperationApplications Causes of KickbackAuxiliary Fence How to Make a jig for rip cutting narrow workpieceCutting aids Push Sticks Push BlocksTypes of cuts Cutting TipsHOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard To Change Blade Angle bevel To Adjust the Bevel indicatorTo Change Blade Depth To position the Sliding Miter TableTo Check Miter Base Parallelism See Figures 32To Check Miter Fence Alignment To Adjust the Miter tableEccentric Screw Nylock NUT SAW To Set the rip fence Scale indicator to the BladeTo use the Rip Fence Rear LIPTo extend To use Outfeed SupportTo use the table extension To closeSee Figures 40 Adjusting Bolts Adjusting bolts 4Heeling paralleling the blade Framing SquareSee Figures 42 Switch On Switch OFF Switch KEY Switch in Locked PositionMaking a cross cut Cross CUT Place Left Hand on WorkpieceMaking a miter cut Making a RIP cutRIP CUT Bladefence Scale Miter CUT Straight See Figures 46 Making a bevel cross cutMaking a bevel rip cut BevelMaking a compound bevel miter cut Making a NON-THROUGH cut Adjusting HandwheelMaking a Large Panel cut Large Panel CUT RIP FenceNON-THROUGH CUT Blade Guard Removed Push Stick Dado CUT Making a Dado cutOnce all dado cuts are completed To REPLACe the Blade AdjustmentsSee Figures 53 See Figures 56 Combination Adjustment Square Blade BoltTo SET the blade at 0 If the blade is not perfectly verticalTo Check the Alignment of the RIP Fence to the Blade To adjust Quick-StopBlade Rip fence Screws Locking Lever Framing Square General Maintenance MaintenanceAccessories LubricationTroubleshooting Troubleshooting RTS31
Top Page Image Contents