Ryobi RTS31 manual Troubleshooting

Page 43

TROUBLESHOOTING

	Problem	Cause	Solution
Excess vibration.		Blade is out of balance.	Replace blade.
		Blade is damaged.	Replace blade.
		Saw is not mounted securely.	Tighten all hardware.
		Work surface is uneven.	Reposition on flat surface.
			Adjust legs of leg stand.
		Blade is warped.	Check saw blade installation. Replace blade if
			necessary.

Rip fence does not move		Rip fence not mounted correctly.	Remount the rip fence.
smoothly.
		Rails are dirty or sticky.	Clean and wax rails.
		Clamp screw is out of adjustment.	Adjust clamp screw counterclockwise.

Rip fence does not lock at		Clamp screw is out of adjustment.	Adjust clamp screw clockwise.
rear.

Image 43

Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of contentsRead ALL Instructions General Safety Rules Never Operate the SAW on the Floor Specific Safety Rules Never Start a Tool When ANY ROTATiNG COM Ponent is in Contact with the WorkpieceSpecific Safety Rules Symbol Signal Meaning SymbolsElectrical Connection Speed and WiringElectrical Extension CordsGlossary of Terms Product Specifications FeaturesSee Figure Know Your Table SAWTo Turn Your SAW on Switch assemblySwitch KEY Switch in Locked Position Operating ComponentsClamps hex key 3 mm Tools NeededBlades Framing Square Phillips Screwdriver FlatheadFollowing items are included with your table saw Loose PartsMounting Holes AssemblyTo attach the wheel assembly UnpackingTo attach the Leg To install the HandleTo secure/level the saw To open set-up the leg stand To open/close set-up/tear downLEG Stand SET-UPThroat Plate To Install miter FenceTo move the LEG Stand To remove/replace the Throat PlateLocked To check SAW Blade installationTo Change riving knife Positions UnlockedWrench To Install the ANTI-KICKBACK Pawls and Blade GuardSee Figures 15 LargeTo Check and Align the riving knife Saw Blade Vertical AdjustmentTo store push stick To Store the table saw AccessoriesSee Figures 20 Causes of Kickback OperationApplications Basic Operation of the Table SawPush Sticks Push Blocks How to Make a jig for rip cutting narrow workpieceCutting aids Auxiliary FenceCutting Tips Types of cutsHOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard To position the Sliding Miter Table To Adjust the Bevel indicatorTo Change Blade Depth To Change Blade Angle bevelSee Figures 32 To Check Miter Base ParallelismTo Check Miter Fence Alignment To Adjust the Miter tableEccentric Screw Nylock NUT Rear LIP To Set the rip fence Scale indicator to the BladeTo use the Rip Fence SAWTo close To use Outfeed SupportTo use the table extension To extendFraming Square Adjusting Bolts Adjusting bolts 4Heeling paralleling the blade See Figures 40Cross CUT Place Left Hand on Workpiece Switch On Switch OFF Switch KEY Switch in Locked PositionMaking a cross cut See Figures 42Making a miter cut Making a RIP cutRIP CUT Bladefence Scale Miter CUT Straight Bevel Making a bevel cross cutMaking a bevel rip cut See Figures 46Making a compound bevel miter cut Large Panel CUT RIP Fence Adjusting HandwheelMaking a Large Panel cut Making a NON-THROUGH cutNON-THROUGH CUT Blade Guard Removed Push Stick Dado CUT Making a Dado cutOnce all dado cuts are completed To REPLACe the Blade AdjustmentsSee Figures 53 If the blade is not perfectly vertical Combination Adjustment Square Blade BoltTo SET the blade at 0 See Figures 56To Check the Alignment of the RIP Fence to the Blade To adjust Quick-StopBlade Rip fence Screws Locking Lever Framing Square Lubrication MaintenanceAccessories General MaintenanceTroubleshooting Troubleshooting RTS31

TROUBLESHOOTING

Problem