Ryobi RY6202 To Remove Battery Pack, To Install Battery Pack, To Assemble or Remove Blade

Page 10

OPERATION

WARNING:

Always remove battery pack from your saw when you are assembling parts, making adjustments, assembling or removing blades, cleaning, or when not in use. Re- moving battery pack will prevent accidental starting that could cause serious personal injury.

TO REMOVE BATTERY PACK

Locate latches on side of battery pack and depress to release battery pack from your saw. See Figure 4.

Remove battery pack from your saw.

WARNING:

Failure to remove battery pack from saw could result in accidental starting causing possible serious personal injury.

TO INSTALL BATTERY PACK

See Figure 4.

Place battery pack in your saw. Align raised rib on battery pack with groove in saw.

Make sure the latches on each side of your battery pack snap in place and battery pack is secured in saw before beginning operation.

CAUTION:

When placing battery pack in your saw, be sure raised rib on battery pack aligns with groove inside saw and latches snap into place properly. Improper assembly of battery pack can cause damage to internal components.

WARNING:

A5-1/2 in. (140 mm) blade is the maximum blade capac- ity of your saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guard, while thicker blades will prevent blade screw from securing blade on spindle. Either of these situations could result in a serious accident.

TO ASSEMBLE OR REMOVE BLADE

TO ASSEMBLE BLADE:

Remove battery pack from saw.

WARNING:

Failure to remove battery pack from saw could result in accidental starting causing possible serious personal injury.

DEPRESS LATCHES TO

RELEASE BATTERY PACK

 

 

 

450

LATCHES

 

 

3

5

 

 

 

 

 

20

 

 

2

 

 

 

 

 

 

BATTERY

3

 

 

 

PACK

 

2

 

 

 

 

1

45

 

 

 

 

 

 

 

 

 

0

 

 

 

 

1

 

 

 

 

Fig. 4

SPINDLE

LOCK

BUTTON

SPINDLE

50 45

230 2

3

2

1

45

0

1

INNER

 

 

 

 

BLADE

 

LOWER

WASHER

BLADE

OUTER

SCREW

BLADE

BLADE

 

GUARD

 

BLADE WASHER

Fig. 5

HANDLE

Locate latches on side of battery pack and depress to re- lease battery pack from your saw. See Figure 4.

Remove blade wrench (5 mm hex key) from storage area. See Figure 1.

Depress spindle lock button and remove blade screw and outer blade washer. See Figure 5.

NOTE: Turn blade screw clockwise to remove.

Wipe a drop of oil onto inner blade washer and outer blade washer where they contact blade.

WARNING:

If inner blade washer has been removed, replace it be- fore placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.

Page 10

Image 10
Contents Operators Manual Save this Manual for Future ReferenceAccessories Table of ContentsUnpacking General Safety Rules Model Battery Pack ChargerSpecific Safety Rules Additional Rules For Safe OperationImportant Safety Instructions for Charger Important Safety Instructions for Charger Symbol Meaning SymbolsSymbol Name DESIGNATION/EXPLANATION Know Your Cordless Circular SAW FeaturesSwitch ApplicationsOperation To Install Battery Pack To Remove Battery PackTo Assemble or Remove Blade To Remove Blade SAW BladesBlade Guard System ScrewTo Lessen the Chance of Kickback KickbackKickback is Caused by Kickback Blade SET TOO DeepTo Adjust Blade Depth Depth of CUT AdjustmentStarting a CUT To Help Maintain Control Width of CUT Scale RIP Cuts Base AssemblyTo Cross CUT or RIP CUT TOP View of SAW Guideline Front of SAW Blade Guide NotchBlade Guide Notch Guideline To Adjust Bevel SettingGuard To Check To AdjustPositive 0 Bevel Stop To Pocket CUTTo RIP CUT To Assemble Optional RIP GuideBattery Pack Preparation for Recycling MaintenanceDisposal of the Exhausted Battery BatteriesService Model NO. and Serial no