Ryobi RY6202 specifications Important Safety Instructions for Charger

Page 6

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER

To reduce the risk of damage to charger body and cord, pull by charger plug rather than cord when disconnecting charger. Following this rule will reduce the risk of serious personal injury.

Make sure cord is located to that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. Following this rule will reduce the risk of serious personal injury.

An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

a.That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b.That extension cord is properly wired and in good electrical condition; and

c.That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)

25´

50´

100´

Cord Size (AWG)

16

16

16

Note: AWG = American Wire Gage

Do not operate charger with a damaged cord or plug. If damaged, have replaced immediately by a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce the risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not use charger outdoors. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Disconnect charger from power supply when not in use. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

WARNING:

RISK OF ELECTRIC SHOCK. DO NOT TOUCH UNINSULATED PORTION OF OUTPUT CONNECTOR OR UNINSULATED BATTERY TERMINAL.

Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic

Page 6

Image 6
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents AccessoriesUnpacking General Safety Rules Model Battery Pack ChargerSpecific Safety Rules Additional Rules For Safe OperationImportant Safety Instructions for Charger Important Safety Instructions for Charger Symbols Symbol MeaningSymbol Name DESIGNATION/EXPLANATION Know Your Cordless Circular SAW FeaturesSwitch ApplicationsOperation To Remove Battery Pack To Install Battery PackTo Assemble or Remove Blade To Remove Blade SAW BladesBlade Guard System ScrewTo Lessen the Chance of Kickback KickbackKickback is Caused by Kickback Blade SET TOO DeepDepth of CUT Adjustment To Adjust Blade DepthStarting a CUT To Help Maintain Control Width of CUT Scale RIP Cuts Base AssemblyTo Cross CUT or RIP CUT TOP View of SAW Guideline Front of SAW Blade Guide NotchTo Adjust Bevel Setting Blade Guide Notch GuidelineGuard To Check To AdjustPositive 0 Bevel Stop To Pocket CUTTo RIP CUT To Assemble Optional RIP GuideBattery Pack Preparation for Recycling MaintenanceDisposal of the Exhausted Battery BatteriesService Model NO. and Serial no