Ryobi R10633 specifications Specific Safety Rules, Additional Rules For Safe Operation

SPECIFIC SAFETY RULES

Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.

Additional Rules For Safe Operation

■Know your power tool. Read operator’s manual care- fully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.

■Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gage size (A.W.G.) of at least 16 is rec- ommended for an extension cord 100 feet or less in length. A cord exceeding 100 feet is not recom- mended. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. An undersized cord will cause a drop in line voltage result- ing in loss of power and overheating.

Important Rules For Battery Tools

■Battery tools do not have to be plugged into an elec- trical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when changing accesso- ries.

■Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and pos- sible injury.

WARNING:

Batteries vent hydrogen gas and can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately.

■Do not charge battery tool in a damp or wet loca- tion. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

■Your battery tool should be charged in a location where the temperature is more than 50°F but less than 100°F. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

■Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in con- tact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medi- cal attention. Following this rule will reduce the risk of serious personal injury.

Additional Specific Safety Rules

■DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle or motor housing. If both hands are holding the saw, they cannot be cut by the blade.

■Keep your body positioned to either side of the saw blade, but not in line with the saw blade. KICKBACK could cause the saw to jump backwards.

■Do not reach underneath the work. The guard cannot protect you from the blade below the work.

■Check the lower guard for proper closing before each use. Do not operate saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position . If saw is acciden- tally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.

■Check the operation and condition of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.

■Lower guard should be retracted manually only for special cuts such as “Pocket Cuts” and “Compound Cuts”. Raise lower guard by Retracting Handle. As soon as blade enters the material, lower guard must be released. For all other sawing, the lower guard should operate automatically.

■Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.

■NEVER hold piece being cut in your hands or across your leg. It is important to support the work properly to minimize body exposure, blade binding, or loss of con- trol.

■Hold tool by insulating gripping surfaces when per- forming an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator.

■When ripping always use a rip fence for a straight edge guide. This improves the accuracy of cut and re- duces the chance of blade binding.

■Always use blades with correct size and shape (dia- mond vs. round) arbor holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.

Page 4