Ryobi BT3100 manual Safety and International Symbols, No Hands Symbol

Page 6

RULES FOR SAFE OPERATION

■CHECK WITH A QUALIFIED ELECTRICIAN or service personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool is properly grounded.

■USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire extension cords that have 3-prong grounding plugs and 3- pole receptacles that accept the tool's plug.

■DO NOT MODIFY the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician.

■USE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Blades must be rated for at least 5,500 rpm. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe use of accessories are included with the accessory.

■DOUBLE CHECK ALL SETUPS. Make sure blade is tight and not making contact with saw or workpiece before connecting to power supply.

■SECURE THE SAW TO THE LEG STAND OR A WORK- BENCH capable of supporting the load of the saw plus any workpiece. This is necessary to avoid any risk of the saw tipping over.

■MAKE SURE THE WORK AREA HAS AMPLE LIGHT- ING to see the work and that no obstructions will interfere with safe operation BEFORE performing any work using the table saw.

■ALWAYS TURN OFF SAW before disconnecting it, to avoid accidental starting when reconnecting to power supply.

■SAVE THESE INSTRUCTIONS. Refer to them frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance, and repair information.

SYMBOL

MEANING

• Do not expose to rain or use in damp locations.

• NO HANDS SYMBOL

Failure to keep your hands away from the blade will result in serious personal injury.

SAVE THESE INSTRUCTIONS

Page 6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents Product SpecificationsSymbol Meaning Safety Alert Symbol Rules for Safe OperationRead ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Blades Coast After Turn OFFSafety and International Symbols No Hands SymbolElectrical Connection ElectricalExtension Cords Grounding InstructionsGlossary of Terms In. NUT Driver UnpackingTools Needed Socket WrenchLoose Parts List Key Description QuanFollowing items are included with your table saw leg stand E JSliding FeaturesGetting to Know Your SAW ScalePower Switch Operating ComponentsPrecision Ground MICRO-GRAIN Carbide Teeth Speed and WiringBlades LASER-CUT Body Expansion Slots Blade RotationAssembly Assembling LEG StandTo Install Front and Back Rails Assembling Storage BracketsMounting the LEG Stand on the Table SAW Base Handwheel To Install Miter Table and FenceRear Rail END Plug Holder NUT Miter Hole BLever To Install Accessory Table and RIP FenceREMOVING/REPLACING the Throat Plate FIT LIP of Table Into Rear RailSmall HEX Wrench To Check SAW Blade InstallationTo Install Blade Guard Assembly Throat PlateReplacing the Throat Plate Screws Operation Types of Cuts HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard To Remove the Blade Inch Blade Guard Riving KnifeRiving Knife Blade Riving Knife Mounting Plate HEX Nuts ShimsTo Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade To Make a Straight Cross CUT Adjustingmiter Clampfence Quick StopTo Lock Miter Table Miter Slide Lock Slots for Locking Miter TableTo Make a Straight RIP CUT Adjusting ClampTo Make a Miter CUT Miter Table Blade Rear Rail RIP FenceTo Make a Bevel Cross CUT To Make a Bevel RIP CUTAccessory Miter Locking Clamps Rail Clamp To Make a Compound Miter CUTTo Make a Large Panel CUT To Make NON-THROUGH Cuts FeatherboardClamp Push Block Bevel To Make Dado Cuts Backup Washer MaintenanceGeneral Maintenance LubricationScrews Lock NUT To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Stop Bolt LockSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring To Adjust the Bevel Locking LeverTo Align the Miter Locking Clamps Screw SET Front Rail Miter Locking ClampTo Adjust the Sliding Miter Table Assembly To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table Spring Plate Backup HEX NUTChecking Sliding Miter Table Assembly To Check Miter Base ParallelismMaking Adjustments to Sliding Miter Table Assembly Eight screws are visible on the miter base BMiter Indicator To Adjust the Miter FenceTo Adjust QUICK-STOP LIP of BaseTrouble Shooting Problem Cause SolutionRyobi Authorized Service CenterPage Refer to Figure 7672 112 101 110 104 122 103 111 102 105 107 108 113115 116 117 119 118 121 120 109 Parts List Figure See Back page for Ordering InstructionsParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly Blade Guard Assembly 506 500 501 504 502 503 505 Key Description QuanRyobi 10 in mm Table SAW Model NO. BT3100 Parts List for Figure KEY Description QuanOperators Manual 10 in mm Table Saw Model BT3100 Ryobi TECHNOLOGIES, INC
Top Page Image Contents