Sears 113.206930, 113.20680 manual Beveling, Chamferbevel Rabbet CUT

Page 20

when pianing wood 3/4 in, thick and NARROWER than

the holdldownipush b!ock_ tilt the h0td d0wn/push

block so that it clea_s"the top of the cutterguard while

#eeding.

Never plane wood that is thinner than 1/2 in....

because

it }s apt. to split or:Shatter and thus has a greater tenden- cy to kickback,

LILLL_'L"

I I II m

I I I I

I=ml

I'L

!

BEVELING

Adjust the fence to the desired angle . . . tighten fence and guard lock knobs.

Follow the same procedure for jointing or planing.

_ i::'NOTE: Removing only the corner on the edge of a board is known as CHAMFERING.

Normally a chamfer is made with one cut.., therefore,

a cut deeper than t/16 in. may be made_

Use hold down/push blocks for wood under 3 in, wide. Position them so you have control of the workpiece at

all times and so they do not contact the guard orthe cutter head,

,// •

,i¸

:

:=:

:

NOTE: Rabbeting on a Jointer is consid_.red to be a

dangerous operation because it requires removal of the cutter guard and increases the potential of kickback be- cause of excessive depth of cut.

NEVER ATTEMPT TO PERFORM A RABBETING OPERATION ON THIS JOINTER, DO NOTOPERATE

JOINTER/P[ANER WITH CUTTERHEAD OR BELT GUARDS REMOVED.

Rabbet cuts should be made on the Radial Saw or Table Saw by making two cuts with the sawblade or by using the Dado Head or Molding Head. Rabbet cuts can also

:be made using the Shaper or Portable Router.

CHAMFERBEVEL

RABBET CUT

i

• •

•2o

 

i

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PartNo.67036 JOINTER/PLANER onlyJOINTER!PLANER with Legs and Motor Full Oneyear Warranty on Craftsman JOINTER/PLANER Know Your Power ToolRemove Adjusting Keys Wrenches USE Safety GogglesGeneral LocationKickbacks Protection EYES, HANDS, FACE, EARS, BodyUnpacking Checking Contents Assembly Electrical RequirementsConnecting to Power Source Outlet ProngPower Assembly Steps are Complete YOUFor UntilAssembling Steel Legs CHECK! NG Cutter Blades and SCR EWS Truss Side Stiffener Head ScrewJO INTER/PLANER StiffenerINSTALLING Sliding Guard Mounting Recommended Craftsman Motor and Belt GuardsBelt Beltguard Clips LET When Changing Rotation Mounting MotorDirection Rotation Setscrew Wrench Bolt JOINTER-PULLEY Belt Guard InstallationConcave Side UP Sliding Guard Infeed ON-OFF Depth of CUT Switch Handwheel Slide Bracket Cutter GuardFence Knob900STOp ScaleSquare Infeed KnurledInfeedtablemust Always be PARAL- LEL to the Outfeed Table Head Ofinfeed Squaretable FENCE\ Cutter GuardInfeed Table Crowned CUTIIii?i i, i i/ ii!iiI Your Work BenchCardboard Rotate Blade OUT PencilThis Feature is Intended to Prevent Unauthorized Possible View Looking UP for Parts IdentificationWrench Leveling Studs LockscrewsLock the Switch OFF When Machine is Not in USE . . . Remove KEY and Keep tTFeeding the Workpiece Jointing Wood That is Wider than 3Left hand, . , Continue feeding white placing Planing Wood That is Thicker than 3Using the Hold DOWN/PUSH Blocks With the Grain Against the GrainWhen pianing wood 3/4 in, thick and Narrower than BevelingChamferbevel Rabbet CUT Block so that it cleasthe top of the cutterguard whileReplacing Cutter Blades Remove belt guardBlade Wedge FTE R Lockscr EW Screw Small Screwdriver32 IN. Setscrew Wrench Cutter HeadSetsc R EW Mark Slots IN. Setscrew Wrench Head Square Lifter ScrewInstalling Cutter Guard Spring Lower fence and tighten both knobsNewblade Sharpening Cutter BladesWeaken View Looking UP for MotorWhite GREEI4CAT. no Recommended AccessorChart Remedy Part Hardware for Mounting Tool and MotorRSWITCH I0 ooBOX Exploded ViewSTD523t17 Screw, Hex. Hd., 5/t6-18 3/4 KeyPart No.NoNo.No LockSTD551210 Infeed Table Parts ListCraftsman 6-1/8 iNCH 3OtINTER-PLANERMODEL No .20680 Fence Assembly Parts Switch BOX ASM, PartsCraftsman 6-118INCH JOINTER-PLANERMODEL No .20680 LiSTJOINTER/PLANER on LY Form No. SP4401

113.20680, 113.206930 specifications

Sears 113.206930 and 113.20680 represent standout models within the lineage of traditional American retailing, showcasing the storied history of the brand while encapsulating modern retail characteristics. Located within the broad spectrum of Sears' extensive inventory, these models underscore innovation in both technology and customer engagement.

One of the primary features of these Sears models is their signature blend of functionality with user-friendly design. Designed for a comprehensive shopping experience, they often reflect the fundamental shift in consumer behavior. With an emphasis on accessibility, these models were created to cater to a diverse demographic, ensuring that customers could find what they needed with minimal effort.

Among the technologies integrated into these models, a key highlight is their utilization of advanced inventory management systems. These systems are designed to streamline the purchasing process, ensuring that stock levels are effectively monitored and that popular items remain available. This technological innovation not only improves the shopping experience but also enhances the efficiency of store operations.

Additionally, the Sears 113 models are frequently equipped with the latest advancements in point-of-sale technology. With intuitive interfaces and robust operating systems, these models facilitate smoother transactions and quicker checkouts, which are crucial in maintaining customer satisfaction. The emphasis on quick service is particularly important given today’s fast-paced shopping culture.

In terms of characteristics, the Sears 113.206930 and 113.20680 exhibit a commitment to quality and durability. Constructed with materials that withstand heavy usage, these models are designed to offer longevity, aligning with the brand’s reputation for reliability. Furthermore, their aesthetic value reflects contemporary design trends, making them visually appealing additions to any retail space.

Customer interaction is another area where these models shine. They often feature integrated feedback systems, allowing customers to share their shopping experiences promptly. This commitment to customer input not only fosters loyalty but also ensures continuous improvement in service delivery.

Overall, the Sears 113.206930 and 113.20680 capture the essence of a brand that thrives on tradition while embracing innovation. These models serve as a testament to Sears' ability to adapt to changing retail landscapes, making them a vital part of the brand’s ongoing legacy in American retail.
Top Page Image Contents