Husqvarna TS 250 XL manual Tile Cutting Accessories, Parts List

Page 17

15

TILE CUTTING ACCESSORIES

ANGLE GUIDE PROTRACTORMITY MITRE GUIDEBULLNOSE FOLDING STAND

Parts List:

Diag.

Part No.

Qty.

Description

Diag.

Part No.

Qty.

Description

1

542 05 01-04*

1

Frame, Miter

10

N/A

1

Arm, Protractor

2

542 05 01-07*

1

Bar, Locking

11

542 02 00-11*

1

Carriage Bolt, 1/4”-20 x 5/8”

3

542 05 01-05*

1

Clip, Stop

12

542 02 02-44*

1

Wing Nut, 1/4”-20 x 1”

4

542 05 01-06*

1

Spring

13

542 18 97-37*

1

Knob, 1/4”-20 x 1”

5

542 05 01-03*

1

Knob

14

542 05 10-10*

1

Protractor Assy

6

542 18 97-37*

2

Knob, 1/4”-20 x 1”

15

542 02 05-98*

1

Screw, Thumb, 1/4”-20 x 1”

7

542 05 10-20*

1

Miter Assy, 45°

16

542 05 10-30*

1

Holder Assy, Bullnose

8

542 18 97-37*

1

Knob, 1/4”-20 x 1”

17

542 05 10-41*

1

Stand, Tile Saw

9

N/A

1

Sector Plate

18

542 05 01-02*

1

Support Assy, Miter Frame

 

 

 

 

 

 

 

 

RIP GUIDE: P/N 542 05 10-00* - The Rip Guide is a standard accessory supplied with every tile saw. It is used to provide a repeatable position for rip cuts until relocated. The Rip Guide clamps to the machined backstop of the conveyor cart.

ADJUSTABLE PROTRACTOR: P/N 542 05 10-10* - The Protractor can be used to rip cut known angles. The protractor clamps to the backstop.

ANGLE GUIDE : P/N 542 05 10-20* - This is a non- adjustable miter used to quickly position the tile at 45 degrees; either on the left or right side. It is often used for repeated diagonal rip cuts. The Angle Guide clamps to the backstop.

BULLNOSE MITRE GUIDE: P/N 542 05 10-30* -This is a fixed guide that positions the tile for a 45 degree miter cut. The Mitering Guide clamps to the backstop.

MITY MITRE GUIDE: P/N 542 05 01-02* - This is a 45 degree fixture that has an adjustable clamp to hold the tile while miter cutting. The Mitering Guide clamps to the backstop.

FOLDING STAND: P/N 542 05 10-41* - This stable, one piece stand brings a Husqvarna® tile saw to standing level for ease of work. The stand conveniently folds flat for storage and transporting.

The instructions for use and spare parts found in this document are for information only and are not binding. As part of our product quality improvement policy, we reserve the right to make any and all technical modifications without prior notice.

The manufacturer accepts no

responsibility caused by unsuitable

use or modifications.

17

Image 17
Contents Page Contents Symbol Definitions Symboles Definición De Los Simbolos Page Riesgo DE Daño Auditivo Hearing HazardCalifornia Prop 65 Warning Dust WarningPage Instructions could Result in Death or Serious Bodily Injury Safety FirstDo not Assembly Component Identification S T R U C T I O N Indication Information BenefitsMachine Set-Up Water Pump Assembly 5 Set-up Install the Cutting Head AssemblyInstallation & Removal of Cutting Blade Water Pump Safety GuidelinesOperating Procedure Using the Bladeshaft LockMotor Alignment ProceduresDepth Linking Protection Profile Wheel SET-UP and USE Maintenance ProceduresPlunge Cutting MachineWater Pump TROUBLE-SHOOTING Procedure Belt Tensioning with Cam AdjustmentRepairs Spare PartsParts List Tile Cutting AccessoriesDiagram 1 Wiring Diagram 542 20 30-79, 1.5HP, 115V/60/1 Page Notas Remarque International Corporate Office