Hobart Welding Products 252TS, 302 manual Principal Safety Standards

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring – be sure power supply system is properly sized, rated, and protected to handle this unit.

MOVING PARTS can cause injury.

DKeep away from moving parts such as fans.

DKeep all doors, panels, covers, and guards closed and securely in place.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling boards or parts.

DUse proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

1-4. Principal Safety Standards

Safety in Welding and Cutting, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126

Safety and Health Standards, OSHA 29 CFR 1910, from Superinten- dent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.

Recommended Safe Practices for the Preparation for Welding and Cut- ting of Containers That Have Held Hazardous Substances, American Welding Society Standard AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126

National Electrical Code, NFPA Standard 70, from National Fire Protec- tion Association, Batterymarch Park, Quincy, MA 02269.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, from Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices For Occupation And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute, 1430 Broadway, New York, NY 10018.

Cutting And Welding Processes, NFPA Standard 51B, from National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

OM-259 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Processes OM-259Description From Hobart to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesPrincipal Safety Standards About Pacemakers EMF InformationLES Fumé ES ET LES GAZ peuvent ê tre dangereux Signification des symbolesConsignes DE Securite Lire Avant Utilisation UN Choc É Lectrique peut tuerDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un incendie ou une explosionLE Bruit peut affecter l’ouïe DES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peutInformation sur les champs é lectromagné tiques Principales normes de sé curitéConsignes relatives aux stimulateurs cardiaques Specifications InstallationDuty Cycle And Overheating Ampere Models Volt-Ampere CurvesSelecting a Location Dimensions And WeightsDimensions WeightGas Slope Connection Label Tapped Reactor AC-Z And Slope Coils Slope Selection 250 Ampere ModelInductance Selection 300 Ampere Models Socket Socket Information Weld Output Terminals And Selecting Cable SizesRemote 14 Receptacle Information CycleElectrical Service Guide Connecting To 115 Volts AC Duplex ReceptacleVolts Placing Jumper Links And Connecting Input PowerControls Maintenance & TroubleshootingRoutine Maintenance OperationTrouble Remedy TroubleshootingCircuit Diagram For 250 Ampere Model Electrical DiagramsOM-259 Complete Assembly Parts ListPC1 Panel, Front w/Components -1 Item Panel, Front w/Components Rectifier Assembly Support ServiceHobart Welding Products Contact your Distributor for
Related manuals
Manual 40 pages 10.59 Kb Manual 40 pages 47.84 Kb

302, 252TS specifications

Hobart Welding Products has established itself as a trusted name in the world of welding equipment, and among its extensive lineup, the 452,302 model stands out for its exceptional performance and versatility. This MIG welder is designed to meet the needs of both professionals and hobbyists, ensuring high-quality welds in a variety of applications.

One of the main features of the Hobart 452,302 is its robust build quality. Constructed with durable materials, this welder is designed to withstand the rigors of heavy use while maintaining consistent performance. Its compact design allows for portability, making it an excellent choice for on-site jobs or home workshops.

The 452,302 operates on a 230V input power, providing a strong output range that can handle a variety of welding tasks, from thin sheets of metal to thicker materials. It boasts a high maximum output of 230 amps, which allows it to tackle demanding projects with ease. This flexibility makes it suitable for professionals in construction, fabrication, and even automotive repair.

With its excellent arc stability, the Hobart 452,302 ensures ease of use and reduces the chance of defects in welds. The welder features an adjustable wire feed speed, allowing users to dial in the perfect setting for their specific welding task. This customization is crucial for achieving optimal results, as different materials and thicknesses require varying settings.

In terms of technology, the 452,302 integrates advanced thermal overload protection, safeguarding against overheating and prolonging the lifespan of the machine. This feature is particularly beneficial in high-demand environments, where extended periods of operation can lead to equipment failure.

The Hobart 452,302 is also compatible with a range of wire sizes and types, enabling users to expand their welding capabilities. This versatility is enhanced by the welder’s easy connectivity to gas regulators, making it suitable for both gas-shielded and flux-cored welding processes.

In conclusion, the Hobart Welding Products 452,302 is a powerful and versatile MIG welder designed to meet the diverse needs of welders. With its robust build, excellent performance features, and advanced safety technologies, it is a reliable choice for anyone seeking top-quality welding equipment. Whether you're a seasoned professional or an enthusiastic beginner, the 452,302 delivers the performance and durability necessary for successful welds on a variety of projects.
Top Page Image Contents