Chicago Electric 68887 manual Wire Liner may come out with the welding, Back into the Gun

Page 10

SAFETY

SETUP

WARNING

The following steps require applying power to the welder

with the cover open.

To prevent serious injury from fire or electric shock:

1.Do not touch anything, especially not the Ground Clamp, with the Gun or welding wire or an arc will be ignited.

2.Do not touch internal welder components while it is plugged in.

	BASICWELDING	14. Do not touch the Gun’s Trigger.
	BASICWELDING	Plug the Power Cord into its electrical
		Plug the Power Cord into its electrical
		outlet and turn the welder to ON.

	WELDING	15. Point the Gun away from all objects and press the
	WELDING	Trigger until the wire feeds out of the gun two inches.
		Trigger until the wire feeds out of the gun two inches.
		The Wire Liner may come out with the welding
		wire, this is normal, just push the Wire Liner
		back into the Gun.
	TIPS	If the wire does not feed properly and the
	TIPS	Spool is stationary, turn the welder to OFF,
		Spool is stationary, turn the welder to OFF,
		unplug it, and slightly tighten the Feed
		Tensioner clockwise before retrying.

MAINTENANCE

MP FLUX WIRE WELDER

	ITEM 68887
		ON	MIN
		OFF	MAX
D SPEED	Wire	.030″-.035″ Flux-core
	Capacity XX Ga. – X/X″ Steel Plate
	Cables	Electrode – X′
	Cables	Ground Clamp – X′
		Ground Clamp – X′

120V~

Gun

Welding

Wire

Page 10

For technical questions, please call 1-800-444-3353.

SKU 68887

Image 10

Contents Page Table of Contents General SafetySafety Fume and Gas SafetyArc Ray Safety Fumes and Gases can be hazardous to your healthSafety Setup Electrical SafetyFire Safety Welding Welding Tips MaintenanceMaintenance Welder use and careGrounded Welders Tips MaintenanceSymbology Extension CordsSetup Cover AssemblySpecifications To Prevent Serious Injury from Accidental OperationSetup Basic Welding Wire Spool InstallationSpindle Basic Welding Welding Tips Maintenance Hold WireGun Welding Wire For technical questions, please call Wire Liner may come out with the weldingWire, this is normal, just push the Wire Liner Back into the GunTurn the Welder to OFF Setup Basic Welding Welding Tips MaintenanceIncrementally Increase tension Until Wire bends Gun Nozzle Contact TipTo Prevent Serious Injury Basic WeldingTo Prevent Serious INJURY, Fire and Burns Safety Setup Basic Welding Welding Tips Maintenance Control Panel LayoutDuty Cycle Duration of Use Weld Settings ChartWire size and material thickness Gun Concrete slabSetting Up The Weld WeldingSafety Basic Welding TechniqueUp to 2 minutes welding At rated output Hold GUN ClearStrike Test Cleaning the WeldWelding Tips Weld Diagnosis Example Weld DiagramsWorkpiece Heat Control / Weld Penetration To CorrectPenetration Workpiece Heat Control Weld ProblemsPossible Causes and Solutions Weld Not Adhering ProperlyCrooked/Wavy Bead Coat of Slag Over WeldPorosity Excessive SpatterMaintenance Nozzle Inspection, Cleaning, and ReplacementSafety Setup Basic Fire and BurnsContact Tip Inspection, Cleaning, and Replacement Nozzle Contact Tip GunWire Feeds, But Arc Does Not Ignite Wire Feed Motor Runs But Wire Does Not Feed ProperlyWire Creates a Bird’s Nest During Operation TroubleshootingWeak Arc Strength TroubleshootingPower Switch Does Not Light When Switched On Welding Arc Not StableParts List Wiring SchematicParts Lists and Diagrams Assembly Diagram Part 9 Detail Record Product’s Serial Number HereLimited 90 Day Warranty Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800