Grizzly G1029Z instruction manual Length AMP Rating

Page 6

Safety Instructions For Power Tools Cont.

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords if they become damaged.

Minimum Gauge for Extension Cords

 

 

LENGTH

 

AMP RATING

25ft

 

50ft

 

100ft

0-6

18

 

16

 

16

7-10

18

 

16

 

14

11-12

16

 

16

 

14

13-16

14

 

12

 

12

17-20

12

 

12

 

10

21-30

10

 

10

 

No

 

 

 

 

 

 

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool.

13.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories.

14.USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury.

15.DO NOT OVER-REACH.Keep proper footing and balance at all times.

16.REDUCE THE RISK OF UNINTENTION- AL STARTING. On machines with mag- netic contact starting switches there is a risk of starting if the machine is bumped or jarred. Always disconnect from power source before adjusting or servicing. Make sure switch is in OFF position before recon- necting.

17.MANY WOODWORKING TOOLS CAN “KICKBACK” THE WORKPIECE toward the operator if not handled properly. Know what conditions can create “kickback” and know how to avoid them. Read the manual accom- panying the machine thoroughly.

18.CHECK DAMAGED PARTS. Before fur- ther use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, bind- ing of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

19.NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. Do not leave tool until it comes to a complete stop.

20.NEVER OPERATE A MACHINE WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Full mental alert- ness is required at all times when running a machine.

21.NEVER ALLOW UNSUPERVISED OR UNTRAINED PERSONNEL TO OPER- ATE THE MACHINE. Make sure any instructions you give in regards to machine operation are approved, correct, safe, and clearly understood.

22.IF AT ANY TIME YOU ARE EXPERIENC- ING DIFFICULTIES performing the intend- ed operation, stop using the machine! Then contact our service department or ask a qualified expert how the operation should be performed.

G1028Z/G1029 Dust Collector

-3-

Image 6
Contents Manual Insert Micron 2 HP Dust CollectorDust Collector Model G1028Z/G1029Page Table Of Contents Safety Safety Instructions For Power ToolsLength AMP Rating Additional Safety Instructions For Dust Collector G1028Z Wiring Circuit RequirementsGrounding Extension Cords Introduction CommentaryUnpacking Piece InventoryClean Up Site ConsiderationsAssembly Beginning Assembly BaseCollector Body OutletSupport Brackets CollectorFlex Hose Bags Securing collection bag G1028Z/G1029 Dust CollectorInstalling Y inlet G1028Z/G1029 Dust Collector InletGeneral Material SelectionSystem Grounding Plastic DuctFlex-hose grounded to machine G1028Z/G1029 Dust Collector Design Suggestions Bird’s eye planning view G1028Z/G1029 Dust CollectorOperations Test RunMaintenance Bag CleaningLubrication Closure Wire Diagram Machine Data Sheet 6A G1029 Caster Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC