Tool Operation Check, Maintainingthe Pneumatictool

TOOL OPERATION CHECK

CAUTION: Remove all fasteners from tool before performing tool operation check.

1.CONTACT TRIP OPERATION:

A.With finger off the trigger, press the contact trip against the work surface.

THE TOOL MUST NOT CYCLE.

B.Hold the tool off the work surface, and pull the trigger.

THE TOOL MUST NOT CYCLE.

C.With the tool off the work surface, pull the trigger. Press the contact trip against the work surface.

THE TOOL MUST CYCLE.

D.Without touching the trigger, press the contact trip against the work surface, then pull the trigger.

THE TOOL MUST CYCLE.

2.SEQUENTIAL TRIP OPERATION:

A.Press the contact trip against the work surface, without touching the trigger.

THE TOOL MUST NOT CYCLE.

B.Hold the tool off the work surface and pull the trigger.

THE TOOL MUST NOT CYCLE.

Release the trigger. The trigger must return to the trigger stop on the frame.

C.Pull the trigger and press the contact trip against the work surface.

THE TOOL MUST NOT CYCLE.

D.With finger off the trigger, press the contact trip against the work surface. Pull the trigger.

THE TOOL MUST CYCLE.

MAINTAININGTHE PNEUMATICTOOL

When working on air tools, note the warnings in this manual and use extra care evaluating problem tools.

CAUTION: Pusher spring (constant force spring). Caution must be used when working with the spring assembly. The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your hand. Also the edges of the spring are very thin and could cut. Care must also be taken to insure no permanent kinks are put in the spring as this will reduce the springs force.

REPLACEMENT PARTS:

Use only genuine BOSTITCH replacement parts. Do not use modified parts.

ASSEMBLY PROCEDURE FOR SEALS:

When repairing a tool, make sure the internal parts are clean and lubricated. Use Parker “O”-LUBE, Magnalube, or equivalent on all “O”-rings. Coat each “O”-ring with lubricant before assembling.

AIR SUPPLY-PRESSURE AND VOLUME:

Air volume is as important as air pressure. The air volume supplied to the tool may be inadequate because of undersize fittings and hoses, or from the effects of dirt and water in the system. Restricted air flow will prevent the tool from receiving an adequate volume of air, even though the pressure reading is high. The results will be slow operation, misfeeds or reduced driving power. Before evaluating tool problems for these symptoms, trace the air supply from the tool to the supply source for restrictive connectors, low points containing water and anything else that would prevent full volume flow of air to the tool.

-11-

651S5 specifications

The Bostitch 651S5 is an advanced pneumatic stapler designed for a variety of heavy-duty applications, making it a favorite among professional contractors and DIY enthusiasts alike. Known for its robust construction and efficient performance, the 651S5 is ideal for tasks ranging from cabinetry and furniture assembly to roofing and insulation work.

One of the standout features of the Bostitch 651S5 is its impressive power-to-weight ratio. Weighing only 4.5 pounds, this stapler is lightweight, allowing for easy maneuverability without sacrificing performance. The tool is capable of driving staples ranging from 1/4 inch to 9/16 inch, enabling users to tackle diverse projects with ease.

Equipped with a high-capacity magazine, the 651S5 holds up to 160 staples at a time, reducing the need for frequent reloading. This feature significantly enhances productivity, especially during long-term use or when working on extensive projects. Additionally, the rear-loading magazine design facilitates quick and simple staple changes.

The Bostitch 651S5 makes use of a trigger system that provides two modes of operation - sequential and contact firing. This versatility allows users to choose the appropriate firing mode based on their project requirements, enhancing both precision and speed. The sequential mode allows for greater control, while contact firing enables rapid stapling, making it perfect for framing or larger installations.

To ensure consistent performance, the stapler incorporates a powerful motor that maintains pressure and drives staples effectively. The tool's adjustable depth-of-drive feature allows users to control how deep the staple is driven into materials. This is particularly useful for achieving clean finishes and preventing damage to delicate surfaces.

For user comfort and safety, the Bostitch 651S5 includes an ergonomic grip that reduces hand fatigue during extensive use. A tool-free adjustment for exhaust and an integrated safety mechanism further enhance the overall experience, ensuring that users work safely and efficiently.

In summary, the Bostitch 651S5 is a reliable and versatile pneumatic stapler, characterized by its lightweight design, high-capacity magazine, dual firing modes, and adjustable depth settings. These features, combined with its powerful motor and user-friendly interface, make it an essential tool for professionals and serious DIYers looking to achieve efficient and quality results. Whether you're tackling cabinetry, insulation, or other heavy-duty projects, the Bostitch 651S5 stands out as a top choice in the world of pneumatic staplers.