Grizzly H8236 owner manual Troubleshooting, Symptom Possible Cause Solution

Page 19

TROUBLESHOOTING

Symptom

Possible Cause

Solution

 

Air leaking at trig-

1. O-rings in trigger valve housing

1.

O-rings must be replaced

ger valve area.

 

are damaged.

 

& operation of safety nose

 

 

 

 

 

 

must be checked.

 

 

 

 

 

 

 

Air leaking.

 

1. Loose screws in housing.

1.

Tighten screws.

 

 

 

 

2.

Damaged O-ring(s).

2.

Replace O-ring(s).

 

 

 

 

3.

Loose air fitting.

3.

Tighten air fitting & use tef-

 

 

 

 

 

 

lon tape.

 

 

 

 

4.

Damaged housing gasket(s).

4.

Replace gasket(s).

 

 

 

 

 

 

 

Tool

skips

nails/

1. Excessive air pressure.

1.

Reduce air pressure to tool.

staples while dis-

2. Air leaks.

2.

Tighten screws and fittings.

charging.

 

3.

Dirt in nose.

3.

Clean nose.

 

 

4.

Dirt or damage prevents nails

4.

Clean magazine and

 

 

 

 

 

 

 

 

 

/staples from moving freely in

 

inspect/repair damage.

 

 

 

 

magazine.

 

 

 

 

 

 

5.

Inadequate air flow to tool.

5.

Check air fitting, hose,

 

 

 

 

 

 

compressor & air pressure.

 

 

 

6.

Worn O-ring on piston or lack

6.

Replace piston O-ring.

 

 

 

 

of lubrication.

 

Lubricate.

 

 

 

 

7.

Damaged O-rings on trigger

7.

Replace trigger valve O-

 

 

 

 

valve.

 

rings.

 

 

 

 

8.

Worn bumper.

8.

Replace bumper.

 

 

 

 

9.

Cap seal leaking.

9.

Replace cap seal.

 

 

 

 

 

 

 

 

Tool

runs

slowly

1. Undersized air hose.

1.

Use a larger air hose.

 

or has a

loss of

2. Nailer is not lubricated.

2.

Lubricate tool.

 

power.

 

3.

Broken spring in cap assem-

3.

Replace spring.

 

 

 

bly.

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Exhaust port in cap is blocked.

4.

Clean or replace damaged

 

 

 

 

 

 

internal parts.

 

 

 

 

5.

Air pressure too low.

5.

Increase air pressure.

 

 

 

 

 

Fasteners frequent-

1. Nails/staples are the wrong

1.

Use correct nails/staples.

ly jam the

nailer/

 

size.

 

 

 

stapler.

 

2. Nails/staples are bent or dirty.

2.

Use undamaged,

clean

 

 

 

 

 

 

nails/staples.

 

 

 

 

3.

Magazine or nose screws are

3.

Tighten magazine.

 

 

 

 

 

loose.

 

 

 

 

 

 

4.

Driver or driver guide are worn

4.

Replace worn or damaged

 

 

 

 

or damaged.

 

parts.

 

 

 

 

 

 

 

 

 

 

 

 

 

Tool does not fire.

1. Tool is not lubricated.

1.

Lubricate tool.

 

 

 

 

2.

Nail/staple is jammed in maga-

2.

Clear nail/staple from maga-

 

 

 

 

zine or discharge area.

 

zine or discharge area.

 

 

 

3.

Piston shaft is damaged.

3.

Replace piston shaft.

 

 

 

 

4.

Air pressure too low.

4.

Check/increase air

pres-

 

 

 

 

 

 

sure.

 

 

 

 

 

 

 

 

 

Model H8236 2-Piece Brad Nailer/Stapler Kit

-17-

Image 19
Contents Model H8236 Piece Brad Nailer Stapler KIT Page Safety Instructions for Pneumatic Tools SafetyBefore Operating This Equipment Safety Instructions for Pneumatic Tools Additional Safety Instructions for Nailers Staplers Model H8236 2-Piece Brad Nailer/Stapler Kit Foreword Tool Data IntroductionUnpackingInventory SetupModel H8236 Inventory Figure Qty Tool Operating Air Pressure Compressed Air SystemTo check the brad nailer safety nose mechanism Brad Nailer Safety Nose MechanismTo load your stapler OperationsLoading To load your brad nailerTo operate your brad nailer OperatingTo operate your stapler To clear a jammed nail from the dis- charge area Clearing Jammed Nails/StaplesTo clear a jammed staple from the dis- charge area Repair Kit Replacing Pistons RingsCleaningLubricating Cleaning & LubricationBrad PartsNailer Breakdown REF Description Brad Nailer Parts ListDescription Stapler Breakdown and Parts ListSymptom Possible Cause Solution TroubleshootingWarranty and Returns