MULTISET/MULTISET PRO - MSCR/MHCR
Description
The MultiSet/Multiset Pro Channel Remote is a
Channel Remotes use standard
Features
•Streamlined appearance and operations
•A red LED light - to help locate the device in a dark room
•As an individual device, the MultiSet/MultiSet Pro Channel Remote has the capability to recall two presets - a
•When used with a MultiSet/MultiSet Pro Scene Master, the remote has additional applications - on/off, raise/lower and three way of a specific dimmer.
Caution
Caution: Be sure that power to the circuit being controlled has been disconnected by removing fuse or turning circuit breaker off. Installing device with power on may expose you to dangerous voltage and damage the device.
Installation Instructions
Note 1: If replacing an existing device with this device begin with Step #1 of Installation section.
Note 2: If installing this device in new construction begin with Step #4 of Installation section.
Reminder: Disconnect power at panelboard.
1.Remove faceplate from existing device.
2.Unscrew and pull device out of wallbox.
3.Disconnect wires from device. Using a wire box tester, identify and mark the “Hot” and the “Traveler” wires connected to device.
4.Install device per the following notes;
IMPORTANT!
4a. Be sure Multiset Ground wire (bare stranded) is connected to earth ground.
Note: Miswiring, or failure to connect ground, may result in improper operation of device.
Installation and
Operation
LED Indicator: (Fig. A)
Glowing RED = Power On (C)
Operating Instructions
TURN LIGHTS ON TO PRESET
• Tap rocker top once. (A)
TURN LIGHTS
•Tap rocker top twice. (A)
ADJUST LIGHT LEVEL
•Press and hold down rocker top or bottom until desired level is reached. (A or B)
• Release rocker |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
TURN LIGHTS OFF |
|
|
|
|
|
|
| |||
• Tap rocker bottom once or twice. (B) |
|
|
|
|
|
|
| |||
• Lights Fade off. |
|
|
|
|
|
|
|
|
|
|
Note: When properly installed, the Red LED on the remote will be constantly |
|
|
|
|
|
| ||||
|
|
|
|
|
|
| ||||
Fig. A |
|
|
| |||||||
lit at half brilliance. |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
Wiring Notes |
|
|
|
|
|
|
|
|
|
|
Multiset Remote to Wallbox Wire |
|
|
|
|
|
|
| |||
Black | Hot (120V. Source, Must be same phase as dimmer) |
|
|
|
|
|
|
| ||
Yellow | Traveler Wire from MultiSet/MultiSet Pro Dimmer On switch |
|
|
|
|
|
|
| ||
Bare Copper | Earth Ground |
|
|
|
|
|
|
| ||
*Grey | Ground or Neutral |
|
|
|
|
|
|
| ||
* For Remote LED operation connect grey to neutral or ground
Note 1: MSCR/MHCR can control one MultiSet/MultiSet Pro Dimmer or switch from one or multiple locations.
Note 2: MSCR/MHCR must be wired on the same circuit as the device it is controlling.
Note 3: MSCR/MHCR provides manual override for any one device (channel) of a MultiSet/MultiSet Pro system
Note 4: Each circuit feeding dimmers and dimmed loads requires a separate neutral. Shared neutrals will result in undesirable flashing of controlled loads
Note 5: Line voltage must not be supplied by a GFI Breaker
Wiring Diagram
Note: No common neutrals on dimmed circuits.
4b. If using Compli faceplate (sold separately): Before connecting any wires, be sure the Compli faceplate mounting frame is behind the device with alignment tabs facing forward. Tabs should rest within centering holes of Remote’s aluminum mounting strap.
5.After all connections have been made (see wiring diagram and notes!) be certain all wire connectors are firmly attached.
6.Gently place wires and backbox into wallbox (with LED at top of device) and screw in place.
7.Before installing faceplate, restore power to circuit.
8.After testing device for proper operation, install faceplate onto the device.
Master
|
|
|
|
|
|
|
| ON | |
|
|
|
|
|
|
|
| A | B |
120VAC |
| C | D | ||||||
|
|
|
|
|
|
|
| OFF | |
| L |
| N | G |
|
|
| ||
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
To Load
MS
L N
120VAC
To Load
MS
LN
120VAC
To Load
MS |
| R |
|
|
|
N L
120VAC
2
3