Aquacal 155, 120 owner manual Safety Information, Data Plate Nomenclature

Page 34

SAFETY INFORMATION

Notice: Heater NOT Repairable by Owner

WARNING !

Failure to heed the following may result in permanent injury or death.

Heat pumps contain no owner-repairable components. Repairs must not be attempted by untrained and/or unqualified individuals. If service is deemed necessary, contact installing dealer or AquaCal Customer Support at (800) 786-7751.

Refrigerant Circuit Service Only by

Qualified, EPA Certified Technician

WARNING !

Failure to heed the following may result in permanent injury or death.

Heater contains refrigerant under high pressure. Repairs to the refrigerant circuit must not be attempted by untrained or unqualified individuals. Service must be performed only by qualified HVAC technicians. Recover refrigerant to relieve pressure before opening system.

DATA PLATE NOMENCLATURE

1

2

3

4

5

6

7

8

9

10

11

12

A T 1

2

0

A R A E W N A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BRAND

H = HeatWave

AT= AeroTemp

SB = SouthBeach

TZ = Tropez

CAPACITY

100 = 90000 Btus/hr

120 = 109000 Btus/hr

155 = 120000 Btus/hr

VOLTAGE

A - 1/60/208-230

B - 3/60/208 - 230

D - 3/50/380

H - 1/50/200-220

RFRG CONTROL

H - HEAT

R - REVERSING

CURRENT RELEASED REVISION

A - INITIAL RELEASE

OPTIONS

N-NONE

CABINET COLOR

W - CRÈME

B - BLACK

REFRIGERANT

E - R22

T - R407C

Z - R410A

CONTROLS

A - ANALOG

D - DIGITAL

34

Image 34
Contents Installation Guide Page Table of Contents Maintenance and General Operation Eam Important Features of Your New Heat Pump HOW a Heat Pump Works Heat Pump Does Not Make Heat…Safety Information Safety SignalsWater Temperature Safety Water Chemistry SafetyVerify Electrical Power is Present at Heater HEATING- Quick Start & StopProgram Filter Pump Run Time HEATING-QUICK Start & StopTo Begin Heating Continuous Usage and Water Around HeaterHeater Controls Control Panel LayoutHeater Controls Operational & Programming CodesMode Controls Explained, and Starting the Heat Pump Start Up & Setting Operating ControlsApplying Power to The Controller Owner-Level Programming Instructions CompleteChanging The Pool Temperature Set Point Start Up & Setting Operating ControlsSelecting Pool/Spa Thermostat Settings Changing The Spa Temperature Set PointUser Lock Code Option ULC Selecting Call-Flex Pump Options CFO General Maintenance Maintenance Operational RecommendationsSafety During Cleaning Operations Maintain Proper Water Flow Maintenance & OperationControl Water Chemistry Control Irrigation and Storm Run Off Maintain Proper Clearances Around HeaterPool/Spa Blankets Maintenance & Operation Heating TipsHeating in Cooler Weather Pool and Spa Combination HeatingCalculating Initial Heating Time At Start Up Continuous Circulator Pump Operation RequiredFreeze Protection & Extended Shut Down Maintenance & Operation Seasonal Use & Shut DownDuring the Swim Season Winterizing for Hard Freeze ConditionsWinterizing Procedure Planned Maintenance Program 20-Point Planned Maintenance Service Includes the FollowingHeat Pump Running... but is it Heating? TroubleshootingHeat Pump Fails to Operate Water Coming from the Heat PumpTroubleshooting Flowchart Heat Pump Fails to OperateProblem Solved Heat Pump Running... but is it Heating?Testing Water Coming from Heat PumpPage Specific Dealerinformation Follows DEALER-SPECIFIC Table of Contents Level-2 dealer-service Programming Data Plate Nomenclature Physical Characteristics Specifications100 & 120 Models Performance/Size/Weight Water/Electrical Requirements Heating Only Models120AHDE 120BHDE 120DHDT 120HHDT 155AHDE 155BHDE 155DHDT 155GHDE Indoor Installation InstallationPlacement of Heater Outdoor InstallationEquipment Mounting Pad Requirements Irrigation, Rainwater Runoff, and Landscape FeaturesAnchoring Heater to Pad Plumbing Requirements Installation Plumbing RequirementsPlumbing Schematics-Flow 20 to 70-GPM Water in & OUT Connections- TypicalGeneral Requirements Connecting External ControllersElectrical Requirements Code-Specific RequirementsWord Concerning Ground-Fault Protection Electrical RequirementsControls Configuration & Adjustments Entering Service MenuConfiguring for External Controllers JAO or FS2 Controls Configuration & AdjustmentsTime Delay dEL Water Sensor Calibration tSCDefrost Sensor Calibration dSC Checking-Adjusting Water Sensor CalibrationSpa Dead Band Differential dBS Defrost Sensor CalibrationPool Dead Band Differential dBP Changing the Service Lock Code and Back Door Entry Pool Dead Band DifferentialService Adjustable Parameters Level -1 and Level-2 Default SettingsTroubleshooting Using Displayed Codes Interpreting Error CodesVerifying the Mode Jumper Position is Correct Mode Jumper ExplainedRepositioning the Mode Jumper Controls Configuration & Adjustments Defrost Systems- Described To Adjust a Len Gordon Switch Water Flow Pressure Switch AdjustmentLocate Water Pressure Switch and Identify Type To Adjust a TecMark SwitchLen Gordon Style Switch WPS Location TecMark Style Switch To Complete the Adjustment Procedure- Either Brand SwitchContacting the Factory Page 2737 24th St. North St. Petersburg, FL Heat Pump OWNER’S Instructions Getting Familiar with Controls Digital CONTROLLER- Operational Displays Getting Your Heat Pump Started & Stopped Continuous Usage and Water around Unit

120, 155 specifications

Aquacal 155,120 is a highly regarded pool heater known for its efficiency, reliability, and advanced technology. This product stands out in the competitive market of swimming pool heating solutions, making it a popular choice among pool owners and professionals alike.

One of the main features of the Aquacal 155,120 is its high-performance heat exchanger, made from durable titanium. This material ensures resistance to corrosion and enhances the longevity of the heater. The titanium heat exchanger is designed to facilitate maximum heat transfer, providing rapid warming of pool water and ensuring a consistent swimming experience.

The units are equipped with a powerful compressor that utilizes advanced inverter technology. This technology enables the heater to adjust its output according to the pool’s needs, optimizing energy consumption and reducing operational costs. The inverter-driven compressor allows the Aquacal 155,120 to operate quietly, making it ideal for residential settings where noise could be a concern.

Aquacal has designed the unit to be user-friendly, featuring an intuitive digital control panel. This control panel allows users to easily monitor and adjust the temperature settings, ensuring that the water temperature can be maintained at a comfortable level. Additionally, this feature includes programmable settings to enable automatic heating schedules, providing convenience and energy savings for pool owners.

The Aquacal 155,120 is also known for its energy efficiency. With a high coefficient of performance (COP), this heater can deliver more heat output per unit of energy consumed compared to traditional heating systems. This efficiency contributes to a lower carbon footprint, making it an environmentally friendly choice for heating pool water.

Furthermore, the unit is designed with robust insulation, which minimizes heat loss and maximizes energy retention. This insulation helps maintain the desired water temperature for longer periods, reducing the need for frequent reheating and thereby lowering energy expenses.

In summary, the Aquacal 155,120 is an outstanding choice for pool owners looking for an efficient, reliable, and technologically advanced heating solution. With its titanium heat exchanger, inverter technology, user-friendly control panel, energy efficiency, and excellent insulation, this pool heater stands out as a top contender for modern pool heating needs. Whether for leisure activities or extended swimming seasons, the Aquacal 155,120 ensures a comfortable and enjoyable swimming experience.