Ryobi JM82 General Safety Rules, Work Area, Electrical Safety, Personal Safety, Tool USE and Care

Page 3

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

n Keep your work area clean and well lit. Cluttered

benches and dark areas invite accidents.

nDo not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

nKeep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

nDouble insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three- wire grounded power cord and grounded power supply system.

nAvoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded.

nDon’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

nDo not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

nWhen operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock.

PERSONAL SAFETY

nStay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

nDress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.

n Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents.

nRemove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

nDo not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

nUse safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

nDo not wear loose clothing or jewelry. Contain long hair. Loose clothes, jewelry, or long hair can be drawn into air vents.

nDo not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the tool in unexpected situations.

TOOL USE AND CARE

nUse clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

nDo not force tool. Use the correct tool for your appli- cation. The correct tool will do the job better and safer at the rate for which it is designed.

nDo not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

nDisconnect the plug from power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.

nStore idle tools out of the reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

nMaintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control.

nCheck for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

nUse only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

nKeep the tool and its handle dry, clean and free from oil and grease. Always use a clean cloth when clean- ing. Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool. Following this rule will reduce the risk of loss of control and deterioration of the enclosure plastic.

3

Image 3
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsWork Area General Safety RulesElectrical Safety Personal SafetyService Specific Safety RulesSymbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Extension Cords ElectricalDouble Insulation Electrical ConnectionProduct Specifications FeaturesHeight Adjustment Knob Switch TriggerDepth Adjustment Knob Height Setting ScalePacking List AssemblyINSTALLING/REMOVING the Dust BAG UnpackingTurning ON/OFF the Biscuit Joiner OperationApplications Spline JoinerySetting Depth of CUT Making Fine AdjustmentsDepth of CUT Fence Angle Setting the Fence HeightSetting the Fence Angle Fence HeightSee Figures 9 Making EDGE-TO-EDGE JointsSee Figures 11 Butt JointsMaking Butt Joints Offset Butt JointsJoints Making T- JointsSee Figures 14 See Figures 16 Cutting Vertical BoardsMiter Joints Making Flat Miter JointsSee Figures 18 See Figures 19 Making Edge Miter JointsSee Figures 22 MaintenanceGeneral Maintenance LubricationBlade Screw Outer Washer Inner Blade See Figures 25 Cleaning the Base Assembly and Dust PathCleaning the Dust BAG Accessories TroubleshootingProblem Solution Page Service Model NO. and Serial no

JM82 specifications

The Ryobi JM82 is a versatile and compact jigsaw, ideal for both DIY enthusiasts and professional woodworkers. Known for its powerful performance, the JM82 combines modern technology with user-friendly features to deliver precision cutting in various materials.

One of the standout characteristics of the JM82 is its 7-amp motor, providing ample power for cutting through wood, plastic, and even metal. The variable speed control allows users to adjust the cutting speed from 0 to 3,000 strokes per minute. This feature is essential for matching the cutting speed to the material being worked on, ensuring smooth and efficient cuts.

The JM82 also boasts a unique orbital action, offering four different setting options. This orbital feature enhances the cutting efficiency by allowing the blade to move in a circular motion as well as up and down, effectively reducing the resistance and enabling faster cuts in thicker materials. This level of customization empowers users to tailor their cutting techniques to specific tasks, ranging from intricate curves to straight cuts.

Another notable feature of the Ryobi JM82 is its tool-free blade change system. This mechanism allows users to quickly and easily swap out blades without needing additional tools. The ability to change blades effortlessly enhances productivity and convenience, especially when working on projects that require different blade types for various applications.

The integrated laser guide is another remarkable technological advancement in the JM82. It projects a clear line on the workpiece, ensuring precise alignment and professional-grade results. This feature is particularly useful for intricate cuts and patterns, maximizing accuracy and reducing the likelihood of mistakes.

Ergonomics is a key focus in the design of the JM82. The handle is designed with a soft grip, providing comfort during extended use and minimizing user fatigue. A built-in dust blower keeps the cutting line clear of debris, improving visibility and ensuring clean cuts.

In terms of build quality, the Ryobi JM82 is constructed with durability in mind. The sturdy design and high-quality materials ensure that the jigsaw can withstand rigorous use while maintaining its performance over time.

In summary, the Ryobi JM82 is a powerful, feature-rich jigsaw that caters to a wide range of cutting needs. With its adjustable speed, orbital action, tool-free blade change, integrated laser guide, and ergonomic design, it stands out as a reliable tool for any woodworking project. Whether you're creating intricate designs or making straight cuts, the JM82 delivers precision and performance, making it an essential addition to any toolbox.