Energy Tech Laboratories 5356, 8358, 8357, 6356 Electrical Connections, Installation Clearances

Page 6

 

 

 

60” (1.5m)

 

 

 

MIN

 

3 FT (90cm)

AIR FLOW OUT

12” (30cm)

 

 

 

MIN

 

MIN

GAS

AIR

 

AIR

FLOW

 

FLOW

HEATER

IN

 

IN

Fig. 1: Installation Clearances

When installed in areas where freezing tempera- tures can be encountered, drain the water circuit to prevent possible freeze-up damage. See the Freeze Protection Section.

Electrical Connections

Refer to the unit rating plate below the control panel for precise power requirements for your unit, and for ampacity and over-current protection requirements.

Locate the equipment disconnect means within 3 feet (90cm) of the heater’s electrical enclosure, or as close to the heater as possible. Always satisfy applicable codes and standards.

In sizing power wiring, be especially aware of up- sizing requirements necessary due to wiring distances. Always satisfy applicable codes and standards.

Electrical installation should be done by a licensed electrician only.

This unit is pre-wired to work with external control sys- tems, heat-on-demand options and other external time clock overrides. Refer to the external control system’s instructions, and page 19 of this manual, for installa- tion information.

6

Image 6
Contents Heat Pump Pool & Spa Heater Water Chemistry MaximumContents Or substantial property damage if ignored Installation Considerations IntroductionInstallation Clearances Electrical ConnectionsWater Connections ControlsControls Operating Instructions System Start-UpSeasonal Start-Up or Annual Check Maintenance Summer ShutdownFreeze Protection Troubleshooting Unit is RUNNING, but not HeatingService Call Verification Fault Code Meaning of CodePlumbing Diagrams Water OUT to Pool or SPA Pool Piping for Heat Pump Pool Heater and Gas Pool Heater Units Wiring Diagram 220/240V Single-Phase Wiring Diagram 200/220V Three-Phase Wiring Diagram 380/420V Three-Phase Installing a Remote Control Device Wiring

8357, 8358, 6358, 6356, 5357 specifications

Energy Tech Laboratories represents a cutting-edge approach to sustainable energy solutions, focusing on the development and enhancement of various technologies aimed at optimizing energy efficiency and harnessing renewable sources. In particular, models 6357, 5358, 5356, 5357, and 6356 showcase an array of advanced features designed to meet the challenges of a rapidly changing energy landscape.

Model 6357 is characterized by its high-efficiency solar cells that utilize multi-junction technology. This allows for a remarkable conversion rate of sunlight into electricity, making it suitable for both residential and commercial applications. The integrated energy management system enables users to monitor and control their energy usage in real-time, optimizing output and reducing waste. Moreover, this model is equipped with AI-driven analytics, which can predict energy consumption patterns and adjust energy distribution accordingly.

On the other hand, model 5358 focuses on energy storage solutions, crucial for balancing supply and demand in renewable energy systems. It utilizes advanced lithium-sulfur battery technology, which offers higher energy density and longer lifespan compared to traditional lithium-ion batteries. This enables energy providers and consumers to store excess energy generated during peak production times and utilize it during high-demand periods, significantly enhancing grid stability.

Model 5356 showcases an innovative microgrid technology designed for localized energy generation and distribution. By integrating multiple sources of renewable energy, including wind and solar, this model ensures that energy can be produced and consumed within the same community, minimizing transmission losses and enhancing energy resilience. Its smart grid capabilities allow for automated adjustments based on real-time demand and supply, fostering a sustainable energy ecosystem.

Model 5357 incorporates advanced geothermal energy extraction methodologies, leveraging cutting-edge drilling techniques that minimize environmental impact. This model not only harnesses the Earth’s internal heat but also incorporates integrated systems to ensure efficient energy conversion and delivery.

Finally, model 6356 represents a comprehensive energy management platform that consolidates data from various sources, including renewable energy generators and storage systems. This platform provides users with insightful analytics that drive informed decision-making, enhancing both operational efficiency and sustainability across diverse energy operations.

Together, these models from Energy Tech Laboratories exemplify a commitment to innovation and sustainability, paving the way for a greener, more energy-efficient future.