Master Appliance EC 100-K specifications EC-100 Ecoheat TM, Specifications

	EC-100 ECOHEAT TM
Instruction Manual	HEAT GUN

Please read, understand and keep this manual for future reference.

Model EC-100K Heat Gun Kit

same as above EC 100 Heat Gun plus accessories and carrying case

Accessories in standard kit:

7/8”	1-1/4”	1-15/16”	3-1/8”
reducer reflector		spreader	spreader
35225	accessory kit -
all four tips listed above
35215	carrying case

SPECIFICATIONS

Model EC-100 Heat Gun

2 heat settings, 500° and 1000° F

2 fan speeds: Low & High Resettable thermostat protection 120 Volts Max., 1200W. Max Airflow, 9 CFM, 1100 FPM/720 FPM Size 8 1/4" (L) X 3 1/8" (W) X 7 1/8" (H) Net weight 1 lb.

UL & CUL listed, 3 wire grounding system

DESCRIPTION AND INTRODUCTION

The Ecoheat is an economical, lightweight, multi-use heat gun. Two heat settings — 500° and 1000° F — make it well suited to a wide variety of automo- tive and commercial applications. Because it weighs 1 lb., it's easy to use for extended periods of time, which cuts down on operator fatigue. When not in use, the heat gun can be set down in an upright position on its very stable built-in stand.

Important Safety Instructions

Warning: THIS PRODUCT IS A SOURCE OF VERY HIGH TEMPERATURE FLAMELESS HEAT. AS WITH ANY ELECTRICAL TOOL, WHEN USING HEAT TOOLS, ALWAYS FOLLOW SAFETY PRECAUTIONS TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY.

1.Read and understand this instruction manual before using this product. Save this manual for future reference.

2.WARNING: To reduce the risk of fire or electric shock, do not expose heat guns to rain or moisture. Store indoors. Connect to grounded outlet only.

3.WARNING: This product, when used for soldering and similar applica- tions, produces chemicals known to the State of California to cause cancer and birth defects or other reprodcutive harm.

4.Do not use plug adaptors or remove the ground prong from the plug. This tool is equipped with a 3-prong plug and a 3-wire grounding system. Connect to properly grounded outlets only.

5.Use heat gun only on adequately rated circuits to avoid overheating of electrical systems.

6.This heat gun can produce up to 1000°F (540° C) of flameless heat out of the nozzle. Do not direct this hot air stream at your clothing, hands or other body parts. Do not use as a hair dryer.

7.Do not touch nozzle until cool. Extreme heat is generated in that area. Always hold tool by the handle.

8.Do not touch work surface with nozzle. Keep nozzle face at least 1" away.

9.Keep a clean work area. Messy or cluttered work areas invite accidents or injury.

10.Keep away from children. All visitors should be kept at a safe distance from the work area. Do not let visitors touch the tool or extension cord.

11.Use tool in a well ventilated area. Do not use near flammable liquids or in an explosive environment (where fumes, gases or dust are present).

12.Remove all highly flammable materials and other debris from the work area.

13.Wear safety glasses at all times.

14.When using an extention cord, use only a

3-wire grounded cord with a minimum of 14 gauge capacity. We recommend they be listed by Underwriters Laboratories (UL) in the U.S.A. or (CSA) Canadian Standards Association in Canada and be suitable for outdoor use. Cords marked for out door use are also suitable for indoor use.

15. Don't abuse cordset. Never yank by cord to remove from electical outlet or carry tool by cord.

16.When not using, place tool on a level sur- face and set heat gun down in an upright position.

17.Keep a fullly charged fire extinguisher close at hand.

18.Do not leave heat gun unattended while running or cooling down.

19.Stay alert. Do not operate tool when you are tired. Use common sense and watch what you are doing.

20.Store properly. Do not store while hot. Store in a dry, high or locked-up location. Keep out of the reach of children.

21.Do not attempt to repair or disassemble this heat gun yourself.

For service information see the Warranty information on the last page of this manual section.