Crane Plumbing 8XSE-HA operation manual Power Cable to Lift Pump, Control Cable to Lift Pump

Page 6

If a rigid conduit is used to install the pump it must meet Class I, Division 1 requirements of the National Electrical Code. Conduit must be stainless steel or coated metal, resistant to sewage water.

C-3) Liquid Level Controls: Intrinsically Safe

WARNING ! - Level control floats used within the hazardous location, must be in an intrinsically safe control circuit suitable for use in CLASS I,

GROUPS C & D, HAZARDOUS LOCATIONS.

The level controls are to be supported by a mounting bracket that is attached to the sump wall, cover or junction box. Cord grips are used to hold the cords in place on the mounting bracket. The control level can be changed by loosening

the grip and adjusting the cord length as per the plans and specifications. Be certain that the level controls cannot hang up or foul in it’s swing and that the entire pump is still submerged when the level control is in the “Off” mode.

A Warrick Control® intrinsically safe relay, Series 27, is an acceptable panel mounted relay, providing the relay is properly installed and maintained.

The primary (A.C. supply line) circuit is not intrinsically safe, therefore the relay must be located in a “SAFE” location (a place that is not classified as a hazardous location). The secondary circuit is intrinsically safe, however, any splice must be made in a “SAFE” location and any control cord that is cut or damaged must be replaced immediately.

C-3.1) Level Control Float System:

It is recommended to use a two float, on and off, level control system. An additional float, incorporated with an alternator switching system will be required for a duplex system. A high level alarm may be required to alert maintenance personnel. A low level cut off may be required to provide system shutdown if the main level control system malfunctions. The off or low level float should be positioned so that the liquid level never drops below the minimum submergence level.

C-4) Electrical Connections:

WARNING! - All model pumps and control panels must be properly grounded per the National Electric Code or Canadian Electric Code, state, province and local codes. Improper grounding voids warranty.

All electrical controls and motor starting equipment must be installed outside the hazardous area unless approved explosion proof controls are used.

C-4.1) Power Cable:

The cord assembly mounted to the pump must not be modified in any way except for shortening to a specific application. Any splice between the pump and the control panel must be made in accordance with all applicable electric codes. It is recommended that a junction box (if used) with seal fittings be mounted outside the sump or be of at least Nema 7 (EEMAC-7) explosion proof construction if located within the wet well. A UL listed seal fitting MUST be used in conduit leaving the hazardous location. DO NOT USE THE

POWER CABLE TO LIFT PUMP.

C-4.2) Control Cable:

The cord assembly mounted to the pump must not be modified in any way except for shortening to a specific application. Any splice between the pump and the control panel must be made in accordance with all applicable electric codes. It is recommended that a junction box (if used) with seal fittings be mounted outside the sump or be of at least Nema 7 (EEMAC-7) explosion proof construction if located within the wet well. A UL listed seal fitting MUST be used in conduit leaving the hazardous location. DO NOT USE THE

CONTROL CABLE TO LIFT PUMP.

C-4.3) Wire Size:

If additional cable is required consult a qualified electrician for proper wire size. See table for further electrical information.

THREE PHASE, 200-230 VOLT AC

Power Cable

Motor Lead Number

Green (Ground)

Green

White

2 & 8

Red

3 & 9

Black

1 & 7

 

4, 5 & 6 Together

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Barnes Table of Contents Safety First Single Phase Liquid TemperatureMotor Housing Three PhaseReceiving Service CentersTo the Purchaser StoragePower Cable to Lift Pump Three PHASE, 200-230 Volt ACControl Cable to Lift Pump Three PHASE, 460 Volt AC Moisture and Temperature SensorsOCCURRED, Schedule Maintenance AS Soon AS Possible Cycle or RUN if AN Overload Condition OccursSection D START-UP Operation Typical Thermal Protection Wiring Diagram Section E Preventative Maintenance Section F Service and RepairPart Number Motor & Inner Shaft Seal ServiceSection G Replacement Parts Ordering Replacement Parts Model NumberTrouble Shooting Match Cause Number with Correlating Correction NumberPage Page Parts List QTY DescriptionPump Model Motor with Various Cord Lengths 25FT 30FT 40FT 50FT 75FT 100FTWarranty Registration Barnes Page Page Reports That are not Returned can Delay or Void Warranty START-UP Report For Submersible PumpsElectrical Readings Final CheckManuals Warranty Registration 45356 U.S.A

8XSE-HA specifications

Crane Plumbing has been a respected name in the plumbing industry for decades, and one of its standout products is the Crane Plumbing 8XSE-HA toilet. Designed with modern bathrooms in mind, this toilet model combines cutting-edge technology with a sleek aesthetic, making it a top choice for homeowners and contractors alike.

One of the main features of the 8XSE-HA is its high-efficiency flush system, designed to conserve water without sacrificing performance. Utilizing only 1.28 gallons per flush, it meets WaterSense certification standards. This not only reduces water usage but also helps lower utility bills, making it an environmentally friendly option that appeals to eco-conscious consumers. The toilet's powerful flush technology ensures that waste is removed effectively, reducing the need for multiple flushes.

The 8XSE-HA also boasts a compact design that suits a variety of bathroom sizes, from small powder rooms to spacious family bathrooms. Its elongated bowl provides added comfort while maintaining a streamlined look. The toilet is available in various finishes, allowing it to seamlessly blend into any decor style, from traditional to contemporary.

Technologically, the Crane Plumbing 8XSE-HA features an advanced siphonic flushing system. This system utilizes the principle of siphoning to create a powerful flush, ensuring efficient waste removal with minimal noise. The toilet also includes a fully glazed trapway, which prevents clogs and improves drainage speed. This innovative design reduces the likelihood of blockages and contributes to overall hygiene.

Another notable characteristic of the 8XSE-HA is its easy installation. It is compatible with standard plumbing setups, and many homeowners find that they can install it themselves with minimal tools. The toilet also includes a robust, sturdy construction that guarantees durability and long-lasting performance, making it a reliable choice for any bathroom.

Maintenance is further simplified with a removable seat and easy-to-clean surfaces. The ceramic finish resists staining and discoloration, ensuring that your toilet remains looking fresh and new for years to come. With its combination of style, efficiency, and advanced plumbing technology, the Crane Plumbing 8XSE-HA is an excellent investment for anyone looking to upgrade their bathroom fixtures.
Top Page Image Contents