Bosch Power Tools 1194VSR, 1194AVSR manual Maintenance, Accessories

Page 10

Maintenance

Service

!WARNING Preventive maintenance

performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Autho- rized Bosch Service Station.

TOOL LUBRICATION

Your Bosch tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regreased with a special gear lubricant at every brush change.

CARBON BRUSHES

The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. Only genuine Bosch replacement brushes specially designed for your tool should be used.

BEARINGS

After about 300-400 hours of operation, or at every second brush change, the bearings

should be replaced at Bosch Factory Service Center or Authorized Bosch Service Station. Bearings which become noisy (due to heavy load or very abrasive material cutting) should be replaced at once to avoid overheating or motor failure.

Cleaning

!WARNING To avoid accidents always disconnect the tool from

the power supply before cleaning or performing any maintenance. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.

!CAUTION Certain cleaning agents and solvents damage

plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Accessories

!WARNING If an extension cord is necessary, a cord with

adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3- wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

Tool’s

Cord Size in A.W.G.

Wire Sizes in mm2

Ampere

 

 

 

 

 

 

 

 

Cord Length in Feet

Cord Length in Meters

Rating

 

25

50

100

150

15

30

60

120

3-6

 

 

 

 

 

 

 

 

18

16

16

14

.75

.75

1.5

2.5

6-8

18

16

14

12

.75

1.0

2.5

4.0

8-10

18

16

14

12

.75

1.0

2.5

4.0

10-12

16

16

14

12

1.0

2.5

4.0

12-16

14

12

 

 

 

 

 

 

 

 

 

*Auxiliary handle

*Chuck

*Chuck key

*Depth gauge

*Carrying case (Model 1194VSRK & 1194AVSRK only)

(*= standard equipment) (**= optional accessories)

-10-

Image 10
Contents Importante Power Tool Safety Rules Work AreaSafety Rules for Hammer Drills ServicePage Symbols Functional Description and Specifications Hammer DrillsOperating Instructions LOCK-ON ButtonFastening With ScrewsDrilling Metal Maintenance AccessoriesSécurité électrique Règles de Sécurité GénéralesAire de travail Sécurité des personnesConsignes de sécurité pour les perceuses à percussion RéparationVos vêtements, ce qui pourrait causer des blessures Symboles Description fonctionnelle et spécifications Perceuses à percussionConsignes de fonctionnement Consignes de fonctionnement Ponçage ET Polissage Perçage DES MétauxPerçage DE LA Maçonnerie Brosses MétalliquesEntretien MaintenanceAccessoires NettoyageSeguridad eléctrica Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad personalNormas de seguridad para taladros de percusión ServicioPage Símbolos De Ni-CdDescripción funcional y especificaciones Taladros de percusiónInstrucciones de funcionamiento Sujecion CON Tornillos Consejos de funcionamientoTaladrado CON Velocidad Variable Brocas Para TaladroLijado Y Pulido Taladrado DE MetalTaladrado DE Mamposteria Escobillas DE AlambreAccesorios MantenimientoLimpieza Page Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools