DeWalt DC835KAR, DC825KAR manual Using an Extension Cable, Belt Hook Optional Accessory fig

Page 13

EN G L IS H

WARNING: No connection is to be made to the earth terminal.

Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 3 A.

Using an Extension Cable

An extension cord should not be used unless absolutely necessary. Use an approved extension cable suitable for the power input of your charger (see Technical Data). The minimum conductor size is 1 mm2; the maximum length is 30 m.

When using a cable reel, always unwind the cable completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and adjustment, always remove the battery pack. Always switch off the tool before inserting or removing the battery pack.

WARNING: Use only DEWALT battery packs and chargers.

Inserting and Removing the Battery Pack from the Tool (fig. 2)

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury.

NOTE: Make sure your battery pack is fully charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1.Align the base of the tool with the notch inside the tool’s handle (Fig. 2).

2.Slide the battery pack firmly into the handle until you hear the lock snap into place.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1.Press the battery release buttons (i) and firmly pull the battery pack out of the tool handle.

2.Insert battery pack into the charger as described in the charger section of this manual.

Belt Hook (Optional Accessory) (fig. 1)

WARNING: To reduce the risk of serious personal injury, DO NOT suspend tool overhead or suspend objects from the belt hook. ONLY hang tool’s belt hook from a work belt.

WARNING: To reduce the risk of serious personal injury, ensure the screw (l) holding the belt hook is secure.

Your tool may be equipped with a belt hook (k). The belt hook allows the tool to be suspended from the tool belt to allow hands-free work.

The belt hook can be be attached to either side of the tool to accommodate left- or right- handed users. If the hook is not desired at all, it can be removed from the tool.

To move belt hook, remove the screw (l) that holds the belt hook in place then reassemble on the opposite side. Always tighten the fastening screw to 0.6-0.8 Nm of torque when installing the belt hook onto the machine.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and applicable regulations.

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories.

Proper Hand Position (fig. 6)

WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction.

Proper hand position requires one hand on the main handle (m), as shown.

Variable Speed Trigger Switch (fig. 1)

To turn the tool on, squeeze the trigger switch (a).

To turn the tool off, release the trigger switch.

Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch is fully released.

Use lower speeds for starting holes without a center punch, drilling in metals or plastics, or driving screws. For maximum tool life, use variable speed only for starting holes or fasteners.

NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should be avoided.

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents DC820 DC822 DC825 DC827 DC830 DC832 DC835 DC837 DC840 DC845 Copyright Dewalt Page Page Congratulations Technical DataEN G L is H EC-Declaration of Conformity Definitions Safety GuidelinesEN G L I S H Machinery DirectiveElectrical Safety Work Area SafetyPersonal Safety Power Tool USE and CareBattery Tool USE and Care Safety Instructions for All Impact DrillsService Residual RisksIPM Important Safety Instructions for All Battery ChargersDate Code Position Hot/Cold Pack Delay Charging Procedure figImportant Safety Instructions for All Battery Packs ChargersBattery Pack Battery Cap figLabels on Charger and Battery Pack Storage RecommendationsPackage Contents Electrical SafetyDescription fig Belt Hook Optional Accessory fig Using an Extension CableVariable Speed Trigger Switch fig To Remove the Battery Pack from the ToolWorklight fig Forward/Reverse Control Button figQuick-Release Chuck fig Anvil With Detent Pin figOptional Accessories CleaningCharger Cleaning Instructions Protecting the EnvironmentDAY no Risk Satisfaction Guarantee Rechargeable Battery PackONE Year Free Service Contract ONE Year Full WarrantyPage Page Page N110986 09/11

DC825KAR, DC835KAR specifications

The DeWalt DC835KAR and DC825KAR are professional-grade cordless impact wrenches designed for heavy-duty applications in construction and automotive industries. These models are part of DeWalt’s growing line of high-performance power tools, renowned for their reliability and innovation.

The DC835KAR model boasts a powerful 18V motor that delivers a striking torque of up to 300 ft-lbs, making it ideal for loosening and tightening stubborn fasteners with ease. It features a 1/2-inch square drive with a detent pin, allowing for secure socket retention during use. The compact design of the DC835KAR enhances maneuverability, especially in tight spaces, while the lightweight build reduces user fatigue during extended operations.

On the other hand, the DC825KAR offers an impressive torque output capable of tackling a variety of tasks. The impact wrench features a variable speed trigger, giving users finite control over the speed and power delivery while working. Its 1/4-inch hex chuck allows for quick and easy bit changes, providing versatility when switching between applications. Both models come equipped with a built-in LED light to illuminate dark work areas, enhancing visibility and precision.

DeWalt has integrated advanced battery technology into these impact wrenches, utilizing lithium-ion batteries that deliver longer run times and reduced charge times. This innovative battery management system ensures consistent power delivery and extends tool life. The tools are compatible with DeWalt’s 18V battery platform, allowing users to interchange batteries with other tools within the same range, enhancing overall efficiency on the job site.

In terms of ergonomics, both the DC835KAR and DC825KAR sport a rubberized grip, which provides comfort and ensures a secure hold even during intense applications. The lightweight design also minimizes fatigue, allowing users to tackle challenging tasks without discomfort.

Overall, the DeWalt DC835KAR and DC825KAR impact wrenches are equipped with cutting-edge features and robust technologies that cater to professionals who demand performance, durability, and versatility. Their ability to deliver exceptional torque in a compact form makes them indispensable tools for any serious tradesperson. With DeWalt’s commitment to quality and innovation, these impact wrenches stand out as powerful allies for tackling the toughest fastening challenges.
Top Page Image Contents